Buildability, i.e. the ability of a deposited material bulk to retain its dimmensions under increasing load, is an inherent prerequisite for formwork-free digital construction (DC). Since DC processes are relatively new, no standard methods of characterization are available yet. The paper at hand presents practice-oriented buildabilty criteria by taking various process parameters and construction costs into consideration. In doing so, direct links between laboratory buildability tests and target applications are established. A systematic basis for calculating the time interval (TI) to be followed during laboratory testing is proposed for the full-width printing (FWP) and filament printing (FP) processes. The proposed approach is validated by applying it to a high-strength, printable, fine-grained concrete. Comparative analyses of FWP and FP revealed that to test the buildability of a material for FP processes, higher velocities of the printhead should be established for laboratory tests in comparison to those needed for FWP process, providing for equal construction rates.

Despite all their advantages, load-bearing concrete shell structures with double curvatures are not frequently in use. The main reason is the complexity of their construction. In such a context, this article starts with a brief, critical review of existing technologies while their pros and cons are highlighted. Against that background the authors then propose a new approach for the highly automated fabrication of gridshell structures from variable modules. To demonstrate the feasibility of such a new technology, a demonstrator called ConDIT 1.0, a sphere-like shell structure composed of several frames was designed and built. The frame modules were fabricated automatically using extrusion-based 3D printing and a printable, strain-hardening cement-based composite (SHCC). This article presents the design of ConDIT 1.0, the mechanical material characterization of printed SHCC, the technology of module production, the results of geometry verification for print modules using 3D scanning, and the procedure for the demonstrator’s assembly.

Cycle times at workstations in offsite construction factories fluctuate widely due to various influencing factors. Consequently, relying on average rates, such as length per unit of time, for estimating cycle times proves to be inaccurate, often leading to significant deviations between production schedules and actual operations. To address this issue, this study proposes an estimation system that leverages machine-learning-based prediction, statistical methods, 3D simulation, and computer vision to predict cycle times at the workstation level. Testing of the system on a semi-automated wood-wall framing workstation in a panelized construction factory shows that it reduces the mean absolute error and sum of errors by approximately 36% and 68%, respectively, compared to the fixed rate method. The results also highlight the efficacy of using computer vision data for training machine-learning models for cycle time estimation, the importance of identifying and understanding the factors influencing cycle times, and the impact of random delays on the accuracy of cycle time estimation systems.

The move to lean construction is a lengthy process that may call into question established ways of construction management delivery. The objective of this article is to help businesses take the first step on this route by introducing a few lean manufacturing techniques and practices that may be used on projects over the next few weeks. Although the construction industry has come a long way since its start, the essential technology to change it has not yet found a home. The digital switch has now entered the construction industry to boost production. Artificial intelligence (AI) is a discipline of computer science described as the potential of machines to mimic intelligent human behavior by modelling traditionally complicated problems using human-inspired techniques. Due to its complexity, AI distinguishes itself from lower degrees of digitalization. The complexity of artificial intelligence involves the formation of new circumstances for human collaboration and trust. This dissertation investigates the application of artificial intelligence and the suitable interaction between humans and AI-based technologies. This study attempts to shed light on how the construction industry may close the gap between the potential and actual benefits of artificial intelligence deployment. Comparing the prospective benefits of AI implementation to the present benefits and challenges of AI deployment in the construction industry revealed the disparity.

Interfaces between layers in 3D-printed elements produced by extrusion-based material deposition were investigated on both macro- and micro-scales. On the macro-scale, compression and bend tests were performed on two 3D-printable cement-based compositions (3PCs), namely C1 and C2. The influences of binder composition and time interval between layers on layer-interface strength were critically analyzed. In the context of additive manufacturing, the optimized composition C2, containing pozzolanic additives, exhibited mechanical performance superior to that of the mixture with Portland cement as the sole binder. In particular, Mixture C2 showed a less pronounced decrease in interface tensile strength. Even for time intervals between depositions of two layers as long as 1 day the loss in corresponding flexural strength was below 25%, as compared with C2 specimens tested in the perpendicular direction. In contrast, the decrease in flexural strength measured for C1 specimens amounted to over 90% for the same set of parameters. Higher porosity at the interfaces of the printed concrete layers was identified as the cause for the lower interface strengths of C1. Microscopic observations supported the findings of the macroscopic investigations. While a pronounced recovery (“self-healing”) of the porous, discontinuous interlayers was observed with increasing age for Mixture C2, in case of C1 the filling products grown in the porous interlayer were found to be non-strengthening.

This research raises questions about the possibilities and options of using BIM methodology for wood design and construction associated with software for structure modeling along the asset's cycle life. Likewise, several academic and research initiatives are reviewed. In this sense, this paper aims to establish an appropriate link between two agendas that the architecture, engineering, and construction (AEC) industry, academia, and governments normally handle separately. By conducting several literature reviews (book, journals, and congresses) and extensive software tests (BIM software: Revit, Archicad, Tekla, and Wood plug-ins: AGACAD, Archiframe, Timber Framing 2015, WoodStud Frame, etc.), the state-of-the-art was assessed in both fields, several cases linking BIM and wood are shown in detail and discussed, various theoretical samples are modelled and shown, and the advantages and disadvantages of each technique and stage are explained. On the other hand, although wood construction has been the most common for hundreds of years, this is not the case of BIM Modeling software developments associated with this materiality. Furthermore, since the appearance of materials such as steel and reinforced concrete, all software developments have focused on these materials, leaving aside the possibility of developing applications for use in wood projects. According to previously discussed, it can be concluded that BIM for Wood has been used more frequently in academia and that both fields have several common processes and, in many cases, only a few BIM-wood tools have been used. Thus, disregarding the high potential and high level of benefits that results with the application of these methodologies for the complete building life cycle (design, construction, and operation).

Both drones and laser scanners digitally take the as-built context of an object into the computer and the data taken is transmitted to a Building Information Modeling (BIM) world to create ac-curate 3D models. Although the laser scanner is the leading method of the Scan-to-BIM proce-dure, many professionals indicate drawbacks of the technology and point out the drone is an al-ternative that can improve the shortcomings, leading to the UAV-to-BIM process. Korean con-struction industry plans to implement the drone technology for scrutinizing as-built construc-tion quality by 2025. However, the drone is not popular in the construction projects. Korean universities where Construction Engineering and Management program have been implement-ed are requested to develop a drone curriculum for construction professionals. Since the majori-ty of the professionals are not familiar with drone operation, in order for the schools to be suc-cessful in developing the curriculum, it is very necessary to perform a preliminary experimental study for identifying the essential education contents that are appropriate to drone beginners. The main objective of this paper is to perform the study for the drone beginners and recognize the recommendations and the framework of drone curriculum that will be beneficial for the schools to develop a comprehensive curriculum later on.

This study explores the perspectives and practices of architects regarding the reuse of wood in construction across five South-Central European countries: Slovenia, Serbia, North Macedonia, Bosnia and Herzegovina (BiH), and Montenegro. Based on a survey of architectural professionals, the research explores their attitudes, challenges, and motivations for using reclaimed wood, with a focus on circular construction principles. Key findings reveal unanimous agreement among re-spondents that both their profession and government entities inadequately support or promote wood reuse within the context of circular construction. While architects value reclaimed wood, there are country-specific variations. Environmental benefits, unique aesthetics, historical value, and sustainability are cited as primary motivators for reclaimed wood use. Additionally, re-spondents emphasize the ecological aspect as the most important consideration in wood product reuse, followed by economic and technological factors. Common concerns revolve around the long-term quality and maintenance of wood products. This research provides insights into the challenges and opportunities surrounding reclaimed wood use in South-Central Europe, high-lighting the need for support mechanisms and increased awareness to advance circular construc-tion practices in the region. These findings can have implications for architects and investors by identifying market opportunities, promoting eco-friendly practices, and providing valuable in-sights for future building designs with a focus on reclaimed wood elements within circular con-struction.

A drone performs comparable function to a laser scanner in the construction quality monitoring, following Scan-to-BIM process. Both technologies digitally capture the as-is environment into the computer and the data captured is transferred to a BIM world to create accurate as-built models. Although the laser scanner is the dominant method of the Scan-to-BIM process, a number of digital professionals point drawbacks of the method and present the drone is an alternative that can improve the drawbacks thereby leading to UAV-to-BIM process in parallel with the Scan-to-BIM. Korean construction industry plans to utilize the two technologies for monitoring construction operation quality in major public projects by 2025. While contractors need competent engineers to be competitive in the projects, the two technology applications are not so popular to the construction projects in Korea and very few experts skillful and knowledgeable of the technologies are available. Korean universities are requested to develop the curriculum of the technologies for the contractors. To be successful in progressing the curriculum, it is very essential to implement a preliminary study with the technologies minimizing the potential failure in operating the curriculum later on. This study performs empirical research on the technologies and identify valuable lessons beneficial to develop the UAV-to-BIM curriculum for the construction engineers.

Failure to meet the deadlines for the implementation of investment and construction projects is a problem in all countries of the world, and leads to unstable activity of construction companies. The article studies the most important destabilizing factors affecting the main indicator of sustainable activity of construction companies-the duration of the implementation of an investment and construction projects. To determine and assess the impact of destabilizing factors on the duration of implementation of selected investment and construction projects, a survey was conducted, in which a number of customers, consultants and contractors involved in construction projects took part. Questionnaires developed on the basis of a cluster sample were sent to respondents, 48 responses were received in response to the assessment of destabilizing factors. To analyze the received and grouped information, structural equation modeling using the Smart-PLS program was used. As a result of modeling, a number of results were obtained, the most important of which are the identification of the main reasons that lead to an average (20% - 50%) increase in the duration of projects in the construction sector. The most significant were: the lack of an appropriate procurement program for materials; inefficient scheduling by contractors and instability of construction production; poor-quality processing of incoming information and untimely deci-sion-making due to changes in projects during their implementation. Destabilizing factors con-tribute to an increase in the duration of construction sector projects, which leads to time overruns, cost overruns, and an increase in the negative impact on the overall use of resources. As a result of the study, a set of recommendations was formed, the most important of which is the use of possible compensatory measures that can allow construction companies to eliminate the risks of disrupting construction deadlines for sustainable activities. These compensatory measures include: - recommendations to customers of the construction project; - recommendations to contractors; - recommendations to the consultant. Moreover, the control of destabilizing factors that can cause delays, the improvement of contracts and the precise and clearer definition of all elements of the project can help to reduce the duration of construction, and will allow companies to maintain sustainable activities in the construction industry.

Sustainability is a characteristic manifested in the ability to maintain the necessary level of performance for construction companies when risk factors arise during the implementation of investment and construction projects. The risk factors that arise during the implementation of in-vestment and construction projects differ in nature, degree of influence, and other characteristics. Ignoring these factors and measures to manage them often leads to critical consequences in the form of disruptions in the timing of work. Risk is a combination of the probability and consequences of the occurrence of adverse events. The article considers the concept of risk as a potential possibility of occurrence of adverse situations and related consequences when exposed to these factors. Risk factors are characterized by surprise, discreteness of changes, the presence of threshold values, upon reaching which a transition to a different mode of operation is required. The article discusses the risk factors arising at the construction stage, their classification. A methodology has been developed that includes conducting a survey in the form of a questionnaire in order to collect information about risk factors that affect the implementation of investment and construction projects. Experts with experience in the construction sector were involved in the survey. The processing of the survey results made it possible to assess the significance of various risk factors in investment and construction projects. Thus, statistical and expert methods were used in the study. The results showed that financial, technical, legal, economic, managerial and natural factors have the greatest impact on investment and construction projects. It is recommended to pay special attention to the listed factors when developing measures aimed at preventing risks and their consequences. The methodology described in the study can be used by construction companies in strategic planning. The analysis of the stability of construction companies, depending on their use of various ways to counteract risk factors, allowed us to develop a number of practical recommendations to reduce the impact of the studied factors on achieving the goals of investment and construction projects.

The frame construction of an apartment complex that consists of multiple buildings encounters various uncertainties, owing to the complex relationships among units of work. Currently, the period of such a construction is calculated based on the number of floors of the highest building in the complex. This study quantitatively analyzes an apartment frame construction period using a queue model and evaluates the validity of the estimated period. In this regard, a methodology is proposed for analyzing the construction period by applying the concept of a customer and a server. A case study on the duration of an apartment frame construction is conducted with Korea Land and Housing Corporation, which has supplied the largest number of apartments in South Korea. It was found that the stable state of a queue system was observed when the rate of server utilization was applied to the basement and aboveground floors. However, a stable state was not reached on the ground floor. This study includes non-working days in its calculation and quantitatively analyzes uncertainty factors during construction. Therefore, the findings can be practically utilized to quantitatively plan the durations of work units in an apartment frame construction.

With the development of bioinspired green solutions for sustainable construction over the past two decades, bio-cementation, which exploits the naturally occurring phenomenon of calcium carbonate precipitation in different environments, has drawn a lot of attention in both building construction and soil stabilization. Various types of microorganisms, along with specific enzymes derived from these microorganisms, have been utilized to harness the benefits of bio-cementation. Different application methods for incorporating this mechanism into the production process of the construction material, as well as a variety of experimental techniques for characterizing the outcomes of bio-cementation, have been developed and tested. Despite the success of bio-cementation as a sustainable method to construction has been demonstrated in a significant body of literature at the laboratory scale, the expansion of this strategy to construction sites and field application remains a pending subject. The issue may be attributed to two primary challenges. Firstly, the complexity of the bio-cementation phenomenon is influenced by a variety of factors. Secondly, the extensive body of literature examines various types of microorganisms under different conditions, leading to a wide range of outcomes. Hence, this study aims to examine the recent advancements in utilizing the most commonly employed microorganism, Sporosarcina Pasteurii, to emphasize the significance of influential factors identified in the literature, discuss the findings that have been brought to light, and outline future research directions toward scaling up the process.

unlike the volume, the expression for the surface area of a regular conoid has not yet been obtained by means of direct integration or a differential geometry procedure. As this non-developable form is relatively used in engineering, the difficulty to determine its surface, represents a serious shortcoming for several problems which arise in radiative transfer, lighting and construction, to cite just a few. In order to solve the problem, I conceived the surface as a set of linearly dwindling ellipses which remain parallel to a circular directrix, a typical problem appears when searching the length of such ellipses. I employed a new procedure which, in principle, consists in dividing the surface into infinitesimal elliptic strips to which we have successively applied Ramanujan’s second approximation for the longitude of the ellipse. In this manner, we can obtain the perimeter of any transversal curve pertaining to the said form as a function of the radius of the directrix and the position of the ellipse’s center on the X-axis. Integrating the so-found perimeters of the differential strips for the whole span of the conoid, an unexpected solution emerges through the newly found number psi (ψ) which seems like a refined approximation to the third decimal of Pi but derived from a definite integral equation. As the strips are in truth slanted in the symmetry axis, their width is not uniform and we need to perform some adjustments in order to complete the problem with sufficient precision, but this is discussed separately in the annexes. Relevant implications for mathematical symmetry applied to multifarious architectural and engineering forms can be derived from this finding

In Korea’s air pollutant inventory, construction machinery is a major emission source in the non-road sector. Since 2004, the Korean government has introduced and reinforced emission regulations to reduce the air pollutants emitted from their diesel engines. Since the engine dynamometer test method used in emission regulations has limitations in reflecting emission characteristics under the diverse working conditions of construction machinery, it is necessary to examine the effectiveness of emission regulations and the validity of the emission factors applied as inputs to the air pollutants inventory. This could be done by evaluating engine operation and emission characteristics under real-world working conditions. In this study, 14 units were selected among the excavators, wheel loaders, and forklifts that represent approximately 90% of the registered construction machines in Korea. They were equipped with a portable emission measurement system (PEMS) to measure gaseous emissions and collect engine data under various real-world working conditions. With the reinforcement of emission regulations for the construction machinery from K-tier3 to K-tier4 in Korea, exhaust after-treatment technologies, such as selective catalytic reduction and diesel oxidation catalyst, were applied. Real world NOx were reduced by approximately 83%, and THC 77% and CO by 73%, respectively. Real world NOx + THC of the K-tier3 machines exceeded the laboratory emission limit, but the K-tier4 machines considerably improved despite some differences. The emission factors applied to the air pollutant inventory have been developed using the engine dynamometer test method, but they were considerably underestimated compared with emissions under real-world working conditions. The difference was even larger for the K-tier4 machines. In this study, the possibility of developing emission factor equations that use the engine load factor as a parameter was confirmed by using the engine work 1 g/kW·h segment moving averaging window (MAW) method.

Claims arising frequently in the Architecture, Engineering and Construction (AEC) industry usually result in disputes, leading to all sorts of negative implications for a project. Claims need to be managed efficiently, and in case they evolve into disputes, they need to be resolved as soon as possible so that the construction process can resume. In this paper, a bibliometric review is carried out to explore the existing literature regarding construction claims and dispute resolution methods employed in construction projects. Using VOSviewer and the Scopus database, relevant literature is retrieved and analyzed using keyword searches, including "construction claim” and "construction management". The detected research themes provide future researchers with potential research directions. A gap in the research regarding the emergence of terms such as “blockchain”, “smart contracts”, and "building information modelling (BIM)" appearing only recently after 2020 in the literature regarding the construction claims and disputes research area was determined. Therefore, a content analysis of the most recent publications employing these and other novel technologies is conveyed. Ultimately, the main research trends and potential research directions for assisting researchers and construction professionals in their efforts to address construction claims and disputes in sustainable and efficient ways are discussed.

In the bioprinting process, controlling the motion of bioprinters involves a computer-aided design (CAD) model, converting that model into g-code, and transmitting the motion commands to the bioprinters. The g-code file contains information about the motion of the axes and can be generated using various software. However, a challenge arises when using g-code between different bioprinters. Therefore, the objective of this study was to propose a reliable method for analyzing the differences in 3D bioprinting devices by parameterizing a crucial variable for extrusion bioprinting: the E-value. Four bioprinters from three different manufacturers were used to investigate the extrusion behavior when subjected to the same E-value.

Abstract: Interface risks are inherent in every construction project from start to finish. Identifying and managing these risks effectively in every project phase is crucial for actualising project objectives. This paper shows a comprehensive framework showing several relationships between project stakeholders and how the interface risks between them that influence project execution are identified and managed for the overall construction project success. Firstly, literature review on interfaces and interface risks were car-ried out and how organisations managed interface risks were discussed and secondly, the collection of quantitative data was conducted by means of structured online questionnaires. The sample consisted of 205 construction project professionals who were selected randomly. This group included individuals with various roles in the construction industry, The data was analysed using descriptive statistical methods, including factor analysis, reliability assessment, and calculations of frequencies and percentages. Finally, the results showed all the factors, work culture and organisational approaches that influence interface risk management and ways to identify and manage interface risks effectively.

This study aimed to identify the influencing factors that drive the adoption of smart construction technologies by highway construction companies. Using expert interviews and expert scoring, interview data were collected from 25 experts in the field, and the TOSE framework was proposed based on the TOE framework, identifying four dimensions and fourteen influencing factors. The results were analyzed using the Fuzzy-DEMATEL-ISM method, and the findings were then summarized according to the evaluation criteria to determine the validity of the fourteen hypotheses and the extent to which they drive the adoption of intelligent construction technologies by motorway construction companies. The findings of this paper will be of great value to decision-makers and participants in highway construction companies, as well as to other companies in the construction industry, in their decision to adopt smart construction technologies.

The article presents the methodology for classifying economic regions with regards to selected factors that characterize a region, such as: the economic structure of the region, and thus the share of individual sectors in the economy; employment; the dynamics of the development of individual sectors expressed as an increase or decrease in production value; the population density in the region and also the level of occupational safety. Cluster analysis, which is a method of multidimensional statistical analysis available in Statistica software, was used to solve the task. The proposed methodology was used to group Polish voivodships with regards to the speed of economic development and occupational safety in the construction industry. Data published by the Central Statistical Office was used for this purpose, such as the value of construction and assembly production, the number of people employed in the construction industry, the population of an individual region and the number of people injured in occupational accidents.

Three-dimensional (3D) printing technology, also known as additive manufacturing (AM), has emerged as an attractive state-of-the-art tool for precisely fabricating functional materials with complex geometries, championing several advancements in tissue engineering, regenerative medicine, and therapeutics. However, this technology has an untapped potential for biotechnological applications, such as sensor and biosensor development. By exploring these avenues, the scope of 3D printing technology can be expanded and pave the way for groundbreaking innovations in the biotechnology field. Indeed, new printing materials and printers would offer new possibilities for seamlessly incorporating biological functionalities within the growing 3D scaffolds. Herein, we review the extrusion-based 3D printing modalities emphasizing biosensor applications. We highlighted the application of natural, synthetic, and composite biomaterials as 3D-printed soft hydrogels. Emphasis was placed on the approach by which the sensing molecules were introduced during the fabrication process. Finally, the future perspective was provided.

Synthesis of heterodinuclear 3d transition metal complexes in which two metal ions are introduced in equivalent coordination sites of a ligand is quite uncommon. We have previously shown that the application of the cis-trans isomerization of the oxamido group was able to furnish such a possibility. In the present paper we demonstrate that this synthetic pathway, relying on the possibility of changing the conformation (cis vs trans) of the oxamido group, can be extended to other ligands. Although we have not been able to structurally characterize these complexes, EPR and magnetic data do confirm the efficiency of this reaction pathway. We also demonstrate that the cis-trans isomerization of the oxamido group is not due to a particular property of the ion involved in the reaction. In fact, isomerization is governed by the basicity of the reaction medium. According to the reaction condition, it is possible to favor or not this phenomenon, and to increase the accessibility to a larger number of novel genuine complexes. But the oxophilic character of the lanthanide ions impedes this isomerization in 3d-4f complexes. The very weak magnetic interactions observed in these Cu-Gd complexes can be explained thanks to spin polarization.

Based on three-dimensional optical proximity correction (3D OPC), recent advancements in 3D lithography have enabled the high-fidelity customization of 3D micro-optical elements. However, micron-to-millimeter scale structures represented by Fresnel lens design bring more stringent requirements for 3D OPC, which poses significant challenges to the accuracy of models and the efficiency of algorithms. Thus, a lithographic model based on optical imaging and photo-chemical reaction curve is developed in this paper, and a sub-domain division method with a statistics principle is proposed to improve the efficiency and accuracy of 3D OPC. Both the simulation and the experimental results showed the superiority of the proposed 3D OPC method in the fabrication of the Fresnel lenses. The computation memory requirements of the 3D OPC are reduced to below 1 %, and the profile error of the fabricated Fresnel lens reduced 79.98%. Applying the Fresnel lenses to an imaging system, the average peak signal to noise ratio (PSNR) of the image increased by 18.92 %, and the average contrast of the image enhanced by 36 %. We believe the proposed 3D OPC method can be extended to the fabrication of vision-correcting ophthalmological lenses.

Construction work is physically demanding. The tasks involved in this professional occupation physically exhaust workers and put them at high risk of injury. This work aims to analyze muscle fatigue in civil construction workers, with and without physical activity historical practice. For this purpose, the muscle activity of the Biceps Femoris, Trapezius Transversalis, Erector Spinae Longissimus, was evaluated using surface electromyography. Eleven male civil construction workers aged 26 to 52 years (38.00 ± 9.60), of whom 7 were untrained (N =7) and 4 were trained (N=4) participated in this study. Each subject completed two assessments at two different times. At the first assessment moment, a questionnaire was completed, and the maximum repetition of the deadlift exercise was assessed. At the second assessment, the subjects were assessed while performing the deadlift in four different situations: 50%RM at rest, 80%RM at rest, 80%RM at fatigue, and 50%RM at fatigue. The trained construction workers have higher levels of muscle activity, and there are no significant differences in muscle activation between the fatigued and non-fatigued sets. There appears to be a strong influence of physical exercise on muscle activity and fatigue in civil construction workers.

Highlights: A new material with a bending strength higher than that of concrete was developed using vegetable or fruit waste. The new material maintains the color, taste, and flavor of the original vegetable or fruit. Without water resistant treatment, the material is edible and can be conditioned with seasonings

This publicly available simulation analysis compares baseline construction options versus sustainable options and evaluates both break-even costs as well as environmental effects. The simulation (https://rminator.shinyapps.io/sustain4/) provides users with comparative estimates based upon existing research on costs. This is the first simulation of its type that quantifies multiple sustainable construction options, associated break-even points, and environmental considerations for public use. Results estimate that a 100% solar solution for the baseline 3,000 square foot / 279 square meter house with 2 occupants results in a break-even of 9 years. The simulation includes options for rainwater harvesting or wells, Icynene foam, engineered lumber, Energy Star windows and doors, low flow water fixtures, aerobic / non-aerobic waste treatment or municipal services, and many other options. This is the first simulation of its type to provide publicly available sustainable construction analysis based on research, and it illustrates that sustainable construction might be both green for the environment and green for the pocketbook.

As is known, the construction industry has one of the highest occupational accidents incidence rates among all economic sectors. Currently, Building Information Modeling (BIM) appears as a tool that addresses occupational safety issues throughout the construction life cycle projects, avoiding hazards and risks and, consequently, increasing safety. This work investigates BIM methodology and related technologies application for building safety planning in construction and demonstrates the potential of this technology for the integrated implementation of safety measures during the design phase and the construction site management. The first step consisted of a literature review on the application of BIM in safety in the design and planning phases. Following, to show the potentialities of construction simulation, a case study based on BIM 4D to prevent falls from height was developed. With BIM 4D, it is possible to follow the construction process over time, giving the construction safety technicians’, designers, supervisors and managers the capability to analyse, in each phase, the potential risks and which safety measures should be implemented. BIM can effectively integrate safety measures from the design phase to the construction and use phase and do integrated safety planning within construction planning, leading to reliable safety management throughout the construction process.

While Neural Radiance Fields (NeRF) are gaining increasing interest in various domains as innovative methods for novel view synthesis and image-based reconstruction, their potential application in the realm of Cultural Heritage remains unexplored. Purpose of this paper is to assess the effectiveness of applying NeRF to sets of images of digital heritage objects and sites. The study’s findings demonstrate that NeRF could be valuable when used in combination with or as a comparison to other well-established techniques such as photogrammetry, to expand the possibilities of preserving and presenting heritage assets with enhanced visual fidelity and accuracy. Particularly, NeRF show promising results in improving the rendering of translucent and reflective surfaces, objects with homogeneous textures, and elements with intricate details. In addition, we demonstrate that, when considering the same set of input images (with known camera poses), reducing the image quality or the number of images results in significantly less information loss with NeRF compared to photogrammetry. This suggests that NeRF is preferentially suited for scenarios involving sparse information or low-quality photos or videos, which could be especially valuable in risky or challenging situations.

3D printing is playing an important role in cardiovascular disease by use of personalised models with replication of normal anatomy and pathology with high accuracy and reliability. While 3D printed heart and vascular models are shown to improve medical education, preoperative planning and simulation of cardiac procedures, and enhance communication with patients, 3D bioprinting however, represents a potential advancement of 3D printing technology by printing cellular or biological components, functional tissues and organs that can be used in a variety of applications in cardiovascular disease. Recent advances in bioprinting technology have shown the ability to support vascularisation of large scale constructs with enhanced biocompatibility and structural stability, thus creating opportunities to replace damaged tissues or organs. In this review, we provide an overview of the use of 3D bioprinting in cardiovascular disease with a focus on technologies and applications in cardiac tissues, vascular constructs and grafts, heart valves and myocardium. Limitations and future research directions are highlighted.

Tumor cells evolve in a complex and heterogeneous environment composed of different cell types and an extracellular matrix. Current 2D culture methods are very limited in their ability to mimic the cancer cell environment. In recent years, various 3D models of cancer cells have been developed, notably in the form of spheroids/organoids, using scaffold or cancer-on-chip devices. However, these models have the disadvantage of not being able to precisely control the organization of multiple cell types in complex architecture and are sometimes not very reproducible in their production, and this is especially true for spheroids. Three-dimensional bioprinting can produce complex, multi-cellular, and reproducible constructs in which the matrix composition and rigidity can be adapted locally or globally to the tumor model studied. For these reasons, 3D bioprinting seems to be the technique of choice to mimic the tumor microenvironment in vivo as closely as possible. In this review, we discuss different 3D-bioprinting technologies, including bioinks and crosslinkers that can be used for in vitro cancer models, and the techniques used to study cells grown in hydrogels; finally, we provide some applications of bioprinted cancer models.

Background: The main objective of this study is to develop a customized metatarsophalangeal implant for the treatment of various conditions affecting this specific joint. This approach involves replacing the joint with a custom implant designed specifically to fit each patient's unique anatomical structure. The need for custom implants stems from the obvious lack of size variety available, which presents a major challenge when, the search for the ideal size implant can be a hard task, also when considering the possibility of extensive modification of the bone to adapt it to the available implant. This adaptation, often synonymous with bone reduction, can cause significant post-operative pain for the patient and impact healing time. Methods: A comparative study of modeling software was carried out to select the perfect software, by defining and comparing the relevant criteria. Similarly, the different biomaterial options were examined and compared to select the one best suited to this project, mentioning the imaging modality used to determine the types of images used for our approach. Finally, the 3D printers used in this work were represented, highlighting their technical characteristics. Findings: A resin metatarsophalangeal implant prototype was created using 3D modeling and reconstruction software and tools. Interpretation: Reconstruction and 3D modeling techniques are revolutionizing implant creation, offering customized solutions for patients suffering from metatarsophalangeal joint disorders caused by a wide range of diseases. These results have significant implications for disability management and rehabilitation, encouraging further exploration and progress.

The persistence of diseases that affect construction workforce as a result of activities on construction sites poses a danger to the sustainable development of the industry. This resulted to a huge loss of skilled labour and economic development of the industry and the entire country. The arrival of the fourth industrial revolution (4IR) technologies urges an urgent need to assess the effect of the technology’s biological driver on the construction occupation related diseases. Therefore, this study is aimed at assessing the effect of 4IR on the construction occupation related diseases in Gauteng, South Africa. The study is quantitative in design and questionnaire survey were administered to project and Health and Safety (H&S) managers in Gauteng, South African construction sector using a proportionate simple random sampling technique. For data analysis, the Warp PLS-SEM 8.0 software algorithm was used for the analysis of the collated data. The study found that the effects of the 4IR’s biological driver variables ranges between moderate to high effects for genome sequencing (GENSE) and Neurotechnology (NEURO) respectively. The combined predictive relevance of the two (2) variables predicts 64% of the construction occupation related diseases. This implies that the adoption of the driver would help reduce the causes of construction-related diseases. Hence, implies that continuous deployment of 4IR technologies would ensure that construction occupation related diseases are easily identified and put on alert.

The size of the population and the need for residential spaces are increasing. One possible solution is to add new floors to existing buildings. The positive aspects of such a solution with respect to its socio-economic impact and impact on the environment is that large amounts of carbon dioxide release will be avoided, waste and its treatment will be reduced, and agricultural land and green spaces will be preserved. However, adding floors to existing structures might be structurally challenging, especially in terms of the behavior under seismic actions. This paper presents a numerical study of a reinforced concrete frame in an old building to which new floors are subsequently added. The analysis shows that the frame does not behave as a whole with the old part of the structure, nor does it behave the same as if it were made with rigid joints compared to additional ones connected using hinge joints. The change from the corner (knee) joint to the external joint has its own effect on the distribution of internal forces in the structure as a whole and in the joint in particular.

Aspects are presented on the interpretation of certainties by assessing risks with maximum level in order to establish reasonable limits of acceptance, tolerance or assumption of risks, supplementing environmental risk factors with external, social, financial elements and introducing a category in the work system analysis.Comparative aspects between INCDPM and MEvAR methods are presented as proposals in the associated tables.The conclusions highlight the current aspects implemented in the method and their usefulness.

The validity of our universe as a three-dimensional space (3+1 in relativity) is considered a fundamental fact in physics. In this study, we show that our observed world is thus the output of a prior fundamental operator referred to as an organizer. The organizer is an expansion of projecting operators. It is been shown that identical weighted projecting operators, which are associated with identical particles, generate subspaces of entangled states, whereas groups of unequal weighted coefficients are responsible for finite-size subspaces that are associated with unidentical particles. Considering 3D-subspaces as evidence of the coefficients’ arrangement in our universe, we implement our formalism to describe the implacable vectors, location, momentum, and force within each 3D subspace. By implementing the Heisenberg relation, we drive both the classical and quantum expressions for the laws of motion.

Quantum mechanics introduces the concept of an observer who selects a measuring device and reads the outputs. This measurement process is irreversible. Lately, scholars on quantum collapse phenomena have presented a quantum-like formalism describing the measurement results as an interpretation of the measured object. Note that an observer must read the interpretation results after the interpretation process. Therefore, we propose that the definition of the concept of life should be expanded based on the following concept: A living system decreases entropy, measured results are interpreted, and an internal observer reads the commentary.

Offsite construction is increasingly being presented as a way to increase housing delivery and reduce the housing crisis. Housing Associations play a pivotal role in the delivery of affordable homes and therefore offsite construction could be beneficial in alleviating the crisis. For offsite construction uptake to increase, the conceptual and pragmatic advantages and challenges surrounding offsite housing in relation to evolving social domestic needs to be explored and understood. The purpose of this paper is to discuss the viability of offsite construction as not only a full-service solution to social housing provision, but an integral strategic partner for meeting the range of specialised fabrication needs for these new properties. A literature review is carried out to explore the conceptual and pragmatic advantages and challenges encountered by HAs adopting offsite construction methods. The paper also investigates which the housing tenures are most suited to offsite construction technology. The paper highlighted that whilst individual case studies and example homes offer one mode of justification for Housing Associations to move forward, it is the cumulative effect of cost savings, sustainability, specialised skill sets, labour reduction, structural innovation, and rate of construction that should be weighed and incorporated into this consideration-making process.

Given the importance of the development of urban infrastructure and environmental impacts produced by the civil construction waste (CCW), it is important to correct the handling of CCW with objective solutions that are more environmentally friendly. In that sense the present study aimed to determine indicators that make it possible to estimate the amount of CCW generated from construction sites in the city of Londrina, Parana State, Brazil. The generation of CCW was estimated in a general way, regarding the composition of its mixture, correlated to the gross areas of the buildings studied and their generated volumes of RCC. This generating rate was evaluated in a general way and specifies two types of sites: the new residential and new non-residential constructions. The data required for the development of these indicators was obtained through extensive survey and interviews carried out at the environment secretariat of the City Hall. The generating rate of CCW obtained for non-residential buildings was 0.2052m3/m2 or 170.44kg/m2, for new residential sites was 0.2054m3/m2 or 170.60kg/m2 and for new commercial or non-residential construction sites, it was 0.20453 m3/m2 or 169.85kg/m2. It was also possible to estimate the amount generated annually per inhabitant in the municipality, which is 0.60m3/inhabit.year or 498.55kg/inhabit.year.

In recent years, there have been concerns raised about construction industrialization in China, which have initiated a wave of policy change in both governmental and industrial organizations in order to change the mode of conventional construction. However, the current development level of regional construction industrialization (RCI) in China has not been well-characterized. This study screened preliminary index systems in five dimensions: technical, economic, sustainable, enterprise development and development environment. Based on the data gathered from the questionnaire surveys and subsequently analyzed, twenty-two critical evaluation indicators were identified. Analytic Hierarchy Process (AHP) was then employed to determine the weighting of each indicator. The evaluation method of the development level was formulated on the basis of the evaluation criteria. Jiangsu Province was used as an example in this study, with the development level of this province being comprehensively examined using a combination of the index system and evaluation method. The results show that Jiangsu has a relatively high RCI development level. The data from analysis scores of five dimensions and twenty-two indicators show that the index system is feasible, with evaluation results being consistent with actual practice. These findings provide a good practical reference for making decisions about how best to guide the development of RCI.

The issue of sustainability has long been the subject of interest of the architecture engineering and construction sector. All three aspects of sustainability - economic, environmental and social - can be affected through appropriate construction waste management. Construction and demolition waste (CDW) is one of the largest worldwide waste streams, therefore it is given great attention by all stakeholders (investors, contractors, authorities, etc.). Researches have shown that one of the main barriers to insufficiency CDW recovery is inadequate policies and legal frameworks to manage CDW. It is also one of the EU's environmental priorities. Aim of the article is to confirm the economic potential of construction and demolition waste audit processing through case study. A pre-demolition waste audit has been processed for unused building of shopping center in the town Snina in Slovakia. Subsequently, a comparison of economic parameters (waste disposal costs and transport costs) of recommended CDW management was performed. This comparison confirmed the economic benefits of environmentally friendly construction waste management methods according to the waste audit results, which will also increase the sustainability of construction projects. In addition, the cost parameters of selected waste disposal methods could be another dimension of building information modelling.

Manufacturing of facial epithesis is a complex technological process including several traditional stages of production, accompanied by aggravated psycho-emotional status of the patient. One of the main factors causing discomfort in patients with facial defects is the process of obtaining silicone impressions from the wound surface and the long waiting period for the final epithesis. Active development of digital technologies in medicine and dentistry helps specialists not only to automate most of the traditional stages of manufacturing of dento-mandibular and facial prostheses, but also improves the quality of life of patients by increasing the efficiency of services and reducing the production time of prosthetic structures. The application of digital technologies in the production of facial epithesis was difficult due to the lack of specialized 3D-software for modeling and material for further additive manufacturing of structures. The authors developed a unique technology for 3D modeling and additive manufacturing of facial epithesis, including a 3D CAD module and material for 3D printing. The primary objective was to fabricate immediate facial prostheses in the postoperative period in the shortest possible time until the final epithesis was fabricated.

The present study aimed to characterize the microstructure of a temporary 3D printing resin (Resilab Temp), evaluating the optical properties and mechanical behavior according to different post-processing curing times. For the analysis of the surface microstructure and establishment of the best printing pattern, samples in bar format following ISO 4049 (25 x 10 x 3 mm) were designed in CAD software (Rhinoceros 6.0), printed on the W3D printer (Wilcos), and light-cured in Anycubic Photon at different times (without curing, 16 minutes, 32 minutes, and 1 hour). For the structural characterization, analyses were carried out in FTIR (Fourier Transform Infrared Spectroscopy) and Scanning Electron Microscopy (SEM). The mechanical behavior of the resin was based on flexural strength tests and Knoop microhardness. Color and translucency analysis were performed with a spectrophotometer (VITA Easy Shade Advanced 4.0), which was evaluated following CIELab, using gray, black, and white backgrounds. All analyses were performed immediately after making the samples and repeated after thermal aging with 2 thousand cycles (5-55 °C). The results obtained were statistically analyzed with a significance level of 5%. FT-IR analysis showed about a 46% degree of conversion on the surface and 37% in the center of the resin sample. The flexural strength was higher for the groups polymerized for 32 min and 1h, while the Knoop microhardness did not show a statistical difference between the groups. Color and translucency analysis also did not show statistical differences between groups. According to all the analyses carried out in this study, for the evaluated material, the post-polymerization time of 1 hour can be suggested to improve the mechanical performance of 3D-printed devices.

In recent years, Additive Manufacturing (AM), commonly referred to as 3D printing, has garnered the attention of the scientific community due to its capacity to transform ordinary and traditional items into customized materials at an affordable cost, through various AM processes. Antimicrobial/antibiofilm 3D printed materials are one of the most trending research topics, owing to the growing concerns over the emergence of complex microbial structures called "biofilms" on various surfaces. The review provides an overview of the evolution of additive manufacturing (AM) technologies and their various derivatives, along with a brief description of their materials and applications. It also introduces how biofilms can represent an advantageous lifestyle for microbial populations. The primary objective of this research was to conduct a systematic review on the development of planctonic or biofilm forms of microorganisms on 3D printed materials. The article summarizes commonly studied microorganisms on these materials and presents their 3D printing process, materials, as well as the fields covered by each of the analyzed papers. To the best of our knowledge, this is the first all-inclusive systematic review that amalgamated research conducted in diverse fields to assess the development of biofilms on surfaces produced through three-dimensional printing. Most notably, this review presents a comprehensive account of sustainable approaches for producing antimicrobial materials through 3D printing. Additionally, we assess their advancements in various fields such as medicine, environment, agri-food, and other relevant sectors. The findings of our literature review can be used to recommend appropriate microorganisms, 3D printing materials, and technologies for academic and industrial research purposes focusing on the development of microbial biofilms on 3D printed surfaces. Furthermore, it highlights the potential of environmentally-friendly modified AM technologies to combat biofilms in clinical and non-clinical areas. Our goal with this review is to help readers gain a better understanding of fundamental concepts, inspire new researchers, and provide valuable insights for future empirical studies focused on eradicating biofilms from 3D printed materials.

Recent years have experienced an increase in construction and demolition waste (C&DW), which is the most significant solid waste stream. C&DW is contributing to exceeding all planetary boundaries and presents a range of other issues. In order to better understand the existing research on C&DW, a global bibliographic analysis was undertaken through seven groups of keyword searches and the results visualised using VOCviewer. The results show that C&DW receives only a modest research attention compared to other areas of waste, and this is despite an exponential increase in C&DW research since 2016. The analyses also show that concrete is the most researched material in terms of C&DW, and that reuse, recycling, and circular economy are so far attracting only proportionally modest research attention. This signals a need for further acceleration of the C&DW research, and specifically for more research on reuse, recycling, and circular economy for materials other than concrete.

Design changes seem inevitable in engineering, procurement and construction EPC projects. Such changes create a need for a proactive approach to adjusting project scope, cost and time (the triple constraints) for efficiency and effectiveness in overall delivery. This study investigates the causes and implications of design changes in order to improve design change management practices. Data for the study was obtained through online interviews with New Zealand industry practitioners. Thematic analysis was used to collate the results into meaningful data. The study found that design changes were predominantly caused by clients' inadequate strategic planning, insufficient attention to design, EPC contractors' inadequate design ability, and on-site variations. There were three categories of such design changes: direct impact on the project, the reciprocal and complementary effect on stakeholders, and the far-reaching impact on the community. The study concludes by suggesting improvements, such as strengthening the integration of project teams to enhance design quality, strategic alignment of stakeholders at the planning stage, early contractor involvement (ECI) between the planning and design phases, and improving collaboration between design and construction teams. Further, a combination of high technical skills (e.g. design ability) and soft skills (can-do attitude, interpersonal skills, problem-solving skills, documentation skills, etc.) are needed to effect the desired improvement in design change management.

In contemporary design practices, there is a disconnect between the design techniques used for early-stage design experimentation and performance analysis, and those used for the manufacture and construction. This study addresses the problems in developing an integrated digital design workflow and provides a research framework for integrating environmental performance requirements with robotic manufacturing processes on a construction site. The proposed method enables the user to import a design surface, identify design parameters, set several environmental performance goals, and thereafter simulate and select a robotic building strategy. Based on these inputs, design alternatives are developed and evaluated, considering their robotically simulated constructibility, in terms of their performance criteria. To validate the proposed method, the design is evaluated in an experiment wherein a double-skin facade perforation is generated using the proposed methodology. The results suggest a heuristic feature to improve the simulated robotic constructibility. Moreover, the functionality of the prototype is demonstrated.

In contemporary design practices, there is a disconnect between the design techniques used for early-stage design experimentation and performance analysis, and those used for the manufacture and construction. This study addresses the problems in developing an integrated digital design workflow and provides a research framework for integrating environmental performance requirements with robotic manufacturing processes on a construction site. The proposed method enables the user to import a design surface, identify design parameters, set several environmental performance goals, and thereafter simulate and select a robotic building strategy. Based on these inputs, design alternatives are developed and evaluated, considering their robotically simulated constructibility, in terms of their performance criteria. To validate the proposed method, the design is evaluated in an experiment wherein a double-skin facade perforation is generated using the proposed methodology. Initial results suggest a heuristic feature to improve the simulated robotic constructibility. Moreover, the functionality of the prototype is demonstrated.

Fires in houses are inevitable and they cause loss of life and major repair costs for the damage structure and contents. There is a clear need to prevent its ignition and spread to adjacent areas. This article presents the steps taken, namely: contacts, data collection, tests, analysis and conclusions regarding the accident resulting from the outbreak and spread of a fire, on December 25, 2020, in a traditional Portuguese house in Arganil, Portugal. The owners and the court requested to carry out an expert opinion by a person with specialized technical-scientific knowledge, which led to this work as an expert. the work consists of carrying out observations and data analysis. Then, the observed and analysed data were laboratory tested in order to consistently identify characteristics that lead to the ignition and propagation of the fire. This work identified construction problems, materials used and heat sources that are responsible for the accident. The conclusions may be used to avoid future incidents or accidents with houses of same construction type.

Revolutionizing Lng Plant Construction and its Comprehensive Comparative Analysis And Evaluation Of Modular Design Development Versus Stick-Built Approach For Enhanced Efficiency And Cost-Effectiveness,.Although the utilization of modularization concepts in the LNG industry remains limited, this study focuses on exploring their potential. It is worth noting that modular units typically incur higher costs compared to field erected units due to the additional requirements of structural steel and robustness for transportation purposes.Nevertheless, the increased cost of modularization can often be balanced by conducting the work at the fabrication site instead of on-field construction. This approach reduces the overall project cost by minimizing field construction expenses and shortening the construction schedule. The objective of this paper is to assess and compare LNG modularization options for a newly established LNG facility in comparison to a conventional stick-built plant used as the base case.:The paper delves into various topics related to LNG plant construction, such as the development of modular units, a comprehensive comparison of different options, evaluation of construction schedules and manpower requirements, logistics considerations, and a recommended approach for design and construction. The cost estimates and engineering, procurement, and construction (EPC) schedules are meticulously compared for each option. Additionally, an inshore/near shore gravity base structure (GBS) option is included for further comparison. It is crucial to emphasize that establishing general costs is not possible as each project is distinct and requires individual study and analysis.:Each project has unique characteristics, resulting in varying shapes of cost curves and break-even points. The outcomes of the feasibility evaluation play a crucial role in determining the extent to which the modular approach to construction is advantageous for the specific project at hand. The evaluation takes into consideration multiple factors to determine the potential benefits of adopting a modular construction approach, allowing decision-makers to make informed choices regarding the project's construction methodology

The global demand for rubber is on a steady rise, which is driven by the increasing production of automobiles and the growing need for industrial, medical, and household products. This surge in demand has led to a significant increase in rubber waste, posing a major global environmental challenge. End-of-life tire (ELT) is a primary source of rubber waste, which possesses significant environmental hazards due to its massive stockpiles. While landfilling is a low-cost and easy-to-implement solution, it is now largely prohibited due to environmental concerns. Recently, ELT rubber waste has garnered considerable attention for its potential applications in civil engineering and construction. These applications not only enhance sustainability but also foster a circular economy between ELT rubber waste and the civil engineering and construction sectors. This review article concentrates on the recent research progress and challenges in the civil engineering applications of ELT rubber waste. It also discusses commercially available recycled rubber-based construction materials, their properties, testing standards, and certification. To the best of the authors' knowledge, this is the first time such a discussion on commercial products has been presented.

The construction industry is a resource and energy intensive industry and thus, has been criti-cized due to rising environmental concerns. As a result of that it has gained heightened interest in the concept of Circular Economy (CE) over the last decade to its ability to promote the slowing, reducing, and closing production and consumption cycles of materials and products used in the construction practices. Digital technologies hold potential to enhance the construction industry's ability to integrate the concept of CE in its practices. However, a clear understanding of digital technology (DT) related barriers that hinder practical implementation of CE, appears to be lacking within the sector. In light of this, this study aims to identify the barriers to adopting DTs to im-plement CE practices in the construction industry. To achieve this aim, a systematic literature review was conducted by reviewing twenty-three (23) relevant papers published until January 2024 in Scopus database. The VOS viewer software was used to perform a co-occurrence analysis of keywords to identify new and popular study areas in the field and content analysis was used to analyse the major barriers to adapt DTs to implement CE in the construction industry. The study identified thirty-four (34) barriers to use DTs to implement CE and these were categorized into nine areas such as: infrastructure, organizational, regulatory, standardization, investment, nature of the construction industry, technological, stakeholder and data related barriers. These findings will be beneficial for construction practitioners and policy makers to adopt DTs to integrate CE practices in the construction industry.

The construction business environment is becoming competitive and intense, and Business Models (BMs) are receiving considerable attention as potential sources of sustainable survival and growth. Converse to the linear economy model that industry follows, the Circular Economy (CE) has the potential to create a sustainable construction industry, while creating a sustainable business environment in construction organisations. Nevertheless, in traditional BMs, value is often concentrated on the financial value for the stakeholders; in Circular Economy Business Models (CEBMs), value is seen more broadly by considering a comprehensive range of value chain partners, the environment, and the society. Hence, implementing CE in the construction industry requires reforms in each value chain. Thus, the aim of this paper is to develop a conceptual model for construction organisations' adoption of CEBMs for their organisations. To accomplish the aim, the objectives of this paper are twofold: (i) to define the concept of CEBMs, and (ii) to map the Conceptual CEBMC (Circular Economy Business Model Canvas) as applicable in the construction organisational context. This research adopted a systematic document review, including a content analysis of selected papers. The study contributes significantly by proposing a CEBMC, in which construction organisations could successfully transform their businesses from linear to circular environments.

In this paper, we study semiconic idempotent commutative residuated lattices. After giving some properties of such residuated lattices, we obtain a structure theorem for semiconic idempotent com- mutative residuated lattices. As an application, we make use of the structure theorem to prove that the variety of strongly semiconic idempotent commutative residuated lattices has the amalgamation property.

Due to the inherent risks associated with tunnel construction, including potential collapse, various types of work activities, and challenging visibility and communication conditions, safety management in tunnel projects requires significant investment in terms of cost and time. In this research, we propose and demonstrate a novel smart construction system that utilizes worker location monitoring technology to enhance safety in tunnel construction. The system comprises a wearable beacon integrated into safety helmets, scanners strategically placed at regular intervals inside the tunnel, environmental sensors for monitoring temperature, pressure, and air quality, and mobile devices for collecting and analyzing data on workers and the environment. Through a field demonstration conducted in a Korean tunnel construction site, we validated the effectiveness of the proposed system, which demonstrated real-time monitoring of workers and reliable communication capabilities, leading to improved safety and cost-efficiency in tunnel construction. By implementing the proposed system, we achieved a significant reduction of 37% in monthly construction costs and 77% in annual construction costs compared to conventional methods.

The construction sector has begun to embrace the digital revolution, intending to improve efficiency. How, on the other hand, should the industry adopt digital tools? And how should the connection between humans and technology function? This study aims to shed light on how the construction sector may bridge the gap between AI deployments’s potential and realized advantages. This article presents research based on a comprehensive review of the literature, case studies of Speller Metcalfe, a design-build and refurbishment project in Malvern, England, Jacobsen Construction, a project digitizing the planning process in Salt Lake City, Utah, USA, and Menkes Development Inc., real-time visibility to construction site insights and data-driven decision-making in Toronto, Canada. The experiences gained via this study show that it is feasible to acquire expertise while adopting sophisticated technologies, such as artificial intelligence, by installing fundamental digital tools (AI). However, when it comes to AI, the level of trust between humans and machines will be the deciding element in its success. This article is a pioneering effort in examining the deployment of AI and how people and technology should interact. This study is limited to three case studies and three digital technologies. To further the study, it is suggested to debate the adaptation of AI on the user's premises, gather more empirical data, and examine case studies from different sectors.

Mining is an important industry, accounting for 6.9% of global GDP. However, global development promotes accelerated demand, resulting in the accumulation of hazardous waste in land, sea, and air environments. It reached 7 billion tonnes of mine tailings generated yearly worldwide, and 19 billion solid tailings will be accumulated by 2025. Adding to this, the legacy of environmental damage from abandoned mines is worrying; in Canada there are around 10,000 abandoned mines, 50,000 in Australia, 6,000 in South Africa, and 9,500 coal mines in China, reaching 15,000 by 2050. In this scenario, restoration techniques from mining tailing have become increasingly discussed among scholars due to their potential to offer benefits towards reducing tailings levels, thereby reducing environmental pressure for the correct management and adding value to previously discarded waste. This review paper explores available literature on the main techniques of mining tailing recycling and reuse and discusses leading technologies, including the benefits and limitations, as well as emerging prospects. The findings of this review serve as a supporting reference for decision-makers concerning the related sustainability issues associated with mining, mineral processing, and solid waste management.

Smart primary healthcare building facility services capture a new level of process and operational data through advanced monitoring, enabling experts to use the building facilities to produce significant and efficient healthcare service delivery within the individual spheres of influence. This study assessed the impact of IoT services on achieving smart primary healthcare building facilities in the rural area of South Africa to enhance primary healthcare delivery. The study identified three (3) basic constructs of IoT services that comprised the application of IoT location recognition and tracking services, the application of the IoT high-speed communication network-based services, and the application of IoT-based services. The study is quantitative, and a questionnaire was used to collect data from the project managers and healthcare practitioners working with the primary healthcare agency in South Africa. The study found a variable degree of impact between the three (3) IoT constructs and the achievement of primary healthcare building facility services in South Africa. The study recommends adopting IoT essential services for achieving smart primary healthcare building facility services in the rural areas of South Africa and other developing countries facing similar primary healthcare delivery challenges.

In the information age today, data are getting more and more important. While other industries achieve tangible improvement by applying cutting edge information technology, the construction industry is still far from being enough. Cost, schedule, and performance control are three major functions in the project execution phase. Along with their individual importance, cost-schedule integration has been a significant challenge over the past five decades in the construction industry. Although a lot of efforts have been put into this development, there is no method used in construction practice. The purpose of this study is to propose a new method to integrate cost and schedule data using big data technology. The proposed algorithm is designed to provide data integrity and flexibility in the integration process, considerable time reduction on building and changing database, and practical use in a construction site. It is expected that the proposed method can transform the current way that field engineers regard information management as one of the troublesome tasks in a data-friendly way.

The quick modernisation of Iceland, that rapidly took place from the first decades of the 20th century onwards, did not only bring fishing trawlers and cars into the country. Among all the techniques of modernity, concrete [steinsteypa] was to become the key material that changed the built landscape of the island and was soon adopted by the first Icelandic architects, such as Rögnvaldur Ólafsson (1874–1914) and Guðjón Samúelsson (1887–1950). Interestingly, the main supporter of this material was Guðmundur Hannesson (1866–1946), a medical doctor and town planner who wrote several articles and even a guidebook published in 1921 and titled Steinsteypa. Leiðarvísir fyrir alþýðu og viðvaninga [Concrete. Guidebook for Common People and Beginners]. In a country that was seeking an architectural self-representation, he understood the technical and formal possibilities that concrete could offer: he claimed, “people [...] were trying to change, to build out of a new material with a new form” (Guðmundur Hannesson 1926, 14). This essay aims thus to retrace the rhetoric of Guðmundur Hannesson and his role in writing an Icelandic chapter of the history of concrete, from its early stage of unmodern trial-and-error to the definition of a modern Icelandic architecture.

Wet coffee processing methods will produce wastewater containing organic matter. The high content of organic matter can be utilized as biogas through the anaerobic process. Anaerobic digesters construction can affect removal process of wastewater pollution and biogas quantity. The purpose of this study is to determine the effect of digester construction between conventional digester, CSTR and UASB producing biogas from coffee wastewater. The conventional digester worked without temperature control system as control, a UASB digester, and CSTR digester worked with temperature control system. Biomass volume was about 5 L with 35 days incubation time. Temperature and pH for UASB and CSTR were set within the range 30 – 35^oC and pH 6.0 – 8.0. Based on the feeding variations, UASB has a stable performance with 83.57 ml/day of average biogas production. It has also highest remediation efficiency of COD, BOD and C/N with 85.00±0.34 %, 84.40%± 5.66 and 97.78± 0.57.

Recent researches proved that the underbridge geometry can be reconstructed by mounting a 3D laser scanner on a motorized cart travelling on a walkway located under the bridge. The walkway is moved by a truck and the accuracy of the bridge model depends on the accuracy of the trajectory of the scanning head with respect to a fixed reference system. In this paper, we describe the metrological characterization of a method that uses non-contact systems to identify the relative motion of the cart with respect to the walkway; the orientation of the walkway with respect to the bridge is determined using inclinometers and optical rails, while the position of the truck with respect to the bridge is measured using a conventional odometer. The measurement uncertainty of the proposed system was initially evaluated by numerical simulations and successively verified by experiments in laboratory conditions. The complete system has then been tested in operative conditions; the validity of the proposed approach has been demonstrated by comparing the geometry of buildings reconstructed with the proposed system with the geometry obtained with a static scan. Results evidenced that the errors are approximately 6 mm.

This research discusses the development of a software-centered EdTech (Education Technology) class model through the implementation of a course titled "3D Time Machine" at a 4-year university in Republic of Korea over two semesters. The course focused on teaching 3D modeling software, Blender, within the history department. The primary objective of offering this course was to equip students from the digital generation with the capability to manipulate digital technology effectively. Through studying historical materials and accumulating domain knowledge, students could construct their narratives from their unique perspectives. This aimed to foster their proficiency in digital technology operation, preparing them for an education environment increasingly centered around virtual worlds. As the use of virtual worlds gains prominence in educational settings, there is a growing need to incorporate curricula that prepare students to thrive as well-prepared citizens in future societies. Assessing the digital competencies of contemporary university students and designing instructional models with particular attention to their needs is becoming increasingly important. This research draws insights from interviews, conducted in both face-to-face and written formats, with students who participated in the "3D Time Machine" course. The interviews revealed valuable insights that can be actively incorporated into the development of software-centered EdTech instructional models. They reported that they expanded their perceptions as they learned how to make their ideas tangible. The course helped students overcome their fear of digital technology. In conclusion, the course effectively employs 3D modeling technology, a software-centered EdTech, as a core element in helping students develop their narratives rapidly and diversely, thereby playing a crucial role in their ability to articulate their unique perspectives.

Pure monocular 3D reconstruction is an ill-posed problem that has attracted the research community's interest due to the affordability and availability of RGB sensors. SLAM, VO, and SFM are disciplines formulated to solve the 3D reconstruction problem and estimate the camera’s ego-motion, so many methods have been proposed. However, most of these methods were not evaluated in large datasets, under various motion patterns, had not been tested under the same metrics, and most of them had not been evaluated following a taxonomy, making their comparison and selection difficult. In this research, we performed a comparison of ten publicly available SLAM and VO methods following a taxonomy, including one method for each category of the primary taxonomy, three machine learning-based methods, and two updates of the best methods, to identify the advantages and limitations of each category of the taxonomy and test if the addition of machine learning or the updates made on those methods improved them significantly. Thus, we evaluated each algorithm under the TUM-Mono benchmark and performed an inferential statistical analysis to identify significative differences through its metrics. Results determined that sparse-direct methods significantly outperformed the rest of the taxonomy, and fusing them with machine learning techniques significantly improves the performance of geometric-based methods from different perspectives.

Three-dimensional (3D) printing technologies are transforming the design and manufacture of components and products across a variety of disciplines, however their application in the construction industry is still limited. Material deposition processes can achieve infinite geometries and have advanced from rapid prototyping and model-scale markets to their application in fabricating functional products, large objects and the construction of full-scale buildings. Many international projects have recently been realized and the construction industry is beginning to utilise these dynamic technologies. The potential advantages for integrating 3D printing into house construction are significant, these include the capacity for mass customization of designs and parameters for functional and aesthetic purposes, reduction in construction waste from highly precise material placement, and the use of recycled waste products in layer deposition materials. With the ultimate goal of improving construction efficiency and decreasing building costs, applying Strand7 Finite Element Analysis software, a numerical model was designed specifically for 3D printing in a cement mix incorporated with recycled waste product High Density Polyethylene (HDPE) and found that construction of an arched truss-like roof was structurally feasible without the need for steel reinforcements. The lab sizes prototypes were manufactured based on the destined numerical model by using a 3D printing technology. Currently available 3D printing technologies can be adopted for building construction and this paper discusses the applications, advantages, limitations and future directions of 3D printing as an innovative and viable solution for affordable house construction.

Construction project management and cost management is a difficult process that affects the overall success of construction projects. The success of a construction project can be assessed according to key performance indicators (KPIs). Cost savings and cost optimization over the life of a construction project is one of these KPIs. Cost management is largely performed through intelligent information technology in the construction industry. Information systems and information technologies have seen an increase in use in the management of construction projects. The same goes for cost management. Several studies mentioned in the paper point to this increase in use in recent years also in the management of costs at various stages. Many studies point to the use of information technology and software applications in the field of cost management. Still, to a large extent, there are no surveys focused on the analysis of the impact and impact factor of information technology on cost savings or cost optimization in various phases of construction projects. The research discusses the issue of the impact of information technology on cost management in various phases of a construction project. The main goal of the research is to analyze the influence of information technology factors on cost savings and optimization in individual phases of a construction project. Several statistical methods were used in the research. The resulting model of information technology impact factor was created based on data processing and the use of the AHP method.

The use of New-age (Nano) Modified Emulsions (NME) for the stabilisation of marginal materials for use in the upper-pavement layers of roads have been proven in laboratories, through Accelerated Pavement Tests (APT) and in practice. In addition, material design methods have been developed based on the scientific analysis of granular material mineralogy and the chemical interaction with the binder to design a material compatible NME stabilising agent for naturally available (often marginal) materials. However, the introduction of any new disruptive technology in a traditionally well-established industry, such as the road construction industry, is usually associated with considerable resistance. This is especially relevant when the new technology enables the use of granular materials traditionally considered to be of an unacceptable quality in combination with relatively new concepts such as New-age (Nano) Modified Emulsions (NME). In practice, few road construction projects are without any problems. The introduction of new-technologies obviously makes it an easy target to blame for any non-related problem that may arise during construction. This article aims to assist in pre-empting, recognising, preventing and resolving material or non-material related construction problems through the correct identification of the cause of the problem and recommending the best, most cost-effective way to correct any deficiencies on site.

Most common classifications for acetabular bone defects are based on radiographic two-dimension imaging, with low reliability and reproducibility. With the rise of modern processing techniques based on 3D modelling, methodologies for volumetric quantification of acetabular bone loss are available. Our study aims to describe a new methodology for quantitative assess-ment of acetabular defects, based on 3D modelling, focused on the surface analysis of the integrity of the main anatomical structures of the acetabulum represented by four corresponding sectors (posterior, superior, anterior, and medial). The defect entity is measured as the Area Increase Ra-tio (AIR) detected in all the sectors analyzed on three planes of view (frontal, sagittal and axial) compared to healthy hemipelvises. The analysis was performed on 3D-models from the CT-scan of six exemplary specimens with a unilateral pathological hemipelvis. AIR between the native and the pathological hemipelvis was calculated for each sector, for a total of 48 analysis (range, +0.93% - +171.35%). AIR of >50% were found in 22/48(45.8%) sectors and affected mostly the posterior, medial and superior sectors (20/22, 90.9%). Qualitative analysis showed consistency of the data with the morphological features of the defects. Further studies with larger samples are needed to validate the methodology and potentially develop a new classification scheme.

In the last 20 years, TADs have become one of the topics in orthodontic science, as it becomes one of the effective anchorages in moving teeth in a 3D movement to treat malocclusion and dental-alveolar orthopedic. Problems with the collusion of the roots of the teeth and trauma have hindered the use of these TADs; one of the solutions to keep TADs safe is a step-by-step innovation of procedure to make this anchorage concept using TAD safe. Making surgical guides for single-standing TADs is essential, and in practice, it is virtually possible with the advance of today's CAD/CAM and 3D printers. The content subject in the paper contains two parts: the consideration of why a surgical guide is necessary for the implantation of TADs and the making of the Surgical guide itself.

In this study, we designed a functional neuro-cardiac model to help us examine the role of neuronal regulation and confirm the importance of neural innervation techniques for cardiac tissue regeneration. A three-dimensional (3D) bioprinted neuro-cardiac scaffold composed of a mixture of gelatin-alginate and alginate-genipin-fibrin hydrogels was developed with a 2:1 ratio of AC16 cardiomyocytes (CMs) and retinoic acid differentiated SH-SY5Y neuronal cells (NCs) respectively. A unique semi-3D bioprinting approach was adopted where the CMs were mixed in the cardiac bioink and printed using an anisotropic accordion design to mimic the physiological tissue architecture in vivo. The voids in this 3D structure were methodically filled in using a NCs-gel mixture and cross-linked. Confocal fluorescent imaging using Microtubule-associated protein 2 (MAP-2) antibodies for labeling NCs, and the MyoD1 antibody for CMs revealed functional coupling between the two cell types in the final cross-linked structure. This data confirmed the development of a physiologically functional neuro-cardiac model that can be used to study neuro-cardiac modulation under physiological and pathological conditions.

In recent years, with the development of social media, people are more and more inclined to upload text, pictures and videos on the platform to express their personal emotions, thus the number of short videos is increasing and becoming the first choice for people to socialize. Unlike the traditional way, people can convey their personal emotions and opinions through media other than words, such as video images, etc. for external information. Therefore, the expression and analysis of emotions is not only through text, but also through the analysis of emotional needs in images and videos, and the research scholars have customized products for individual users. Compared with pure text content, video information can more intuitively express users' happiness, anger and sorrow, thus short video-related applications have gained more and more popularity among Internet users in recent years. However, not all short videos on social networking sites can accurately express users' emotions, and related text information can more accurately assist sentiment analysis and thus improve accuracy. However, short video sentiment analysis based on video frame images is inaccurate in some scenarios, such as when expressing tears of joy, the sentiment expressed by the user's facial expression and voice are different, which will cause errors in the analysis of sentiment. As a result, researchers began to consider multimodal sentiment analysis to reduce the impact of the above scenarios on short video sentiment analysis. This paper focuses on proposing a sentiment analysis method for short videos. We first propose a residual attention model to make full use of the information in audio to classify the emotions contained in them. Then the text information in the dataset is classified by feature extraction. The key to extract features from text information is not only to retain the semantic information of the text, but also to explore the potential emotional information in the text, so as to ensure the integrity of the text information features. The experiments show that the sentiment analysis model proposed in this paper is more superior than the baselines.

An approach employing ultrafast laser hybrid subtractive-additive microfabrication combining ablation, 3D nanolithography and welding is proposed for the realization of Lab-On-Chip (LOC) device. Single amplified Yb:KGW fs-pulsed laser source is shown to be suitable for fabricating microgrooves in glass slabs, polymerization of fine-meshes filter out of hybrid organic-inorganic photopolymer SZ2080 inside them, and, lastly, sealing the whole chip with cover glass into a single monolithic piece. The created microfluidic device proved its particle sorting function by separating 1 μm and 10 μm polystyrene spheres in a mixture. All together, this shows that fs-laser microfabrication technology is a flexible and versatile tool for the manufacturing of mesoscale multi-material LOC devices.

Digital twins are gaining in popularity for simulating complex natural and urban environments. In this context, accurate segmentation of objects within 3D urban environments is of crucial importance. The aim of this project is to develop a methodology for extracting buildings from textured 3D meshes. To this end, PicassoNet-II, a semantic segmentation architecture is employed. The methodology also incorporates Markov field-based contextual analysis to assess post-segmentation features. In addition, building instantiation is performed using cluster analysis algorithms. Training this model to fit various datasets requires a large amount of annotated data, both from Quebec City, Canada, and from simulated data. Experimental results show that the use of simulated data improves segmentation accuracy, and the DBScan algorithm proves effective in extracting isolated buildings. This project paves the way for improved applications in 3D urban modeling, offering opportunities in fields ranging from urban planning to resource management. The positive results with simulated data reinforce the impact of this research on improving digital models of our ever-changing urban environments.

3D Zernike moments based on 3D Zernike polynomials have been successfully applied to the field of voxelized 3D shape retrieval and have attracted more attention in biomedical image processing. As the order of 3D Zernike moments increases, both computational efficiency and numerical accuracy decrease. Due to this phenomenon, a more efficient and stable method for computing high-order 3D Zernike moments was proposed in this study. The proposed recursive formula for computing 3D Zernike radial polynomials combines the recursive calculation of spherical harmonics to develop a voxel-based algorithm for the calculation of 3D Zernike moments. The algorithm was applied to the 3D shape Michelangelo's David with a size of 150×150×150 voxels. As compared to the method without additional acceleration, the proposed method uses a group action of order sixteen orthogonal group and saving unnecessary iterations, the factor of speed-up is 56.783±3.999 when the order of Zernike moments is between 10 and 450. The proposed method also obtained an accurate reconstructed shape with the error rate (normalized mean square error) of 0.00 (4.17×10^-3) when the reconstruction was computed for all moments up to order 450.

Conflicts are frequent within the complex professional environment of the construction industry. If claims cannot be overcome amicably, they result in disputes that lead to litigation. Identification of the causes of these claims and their impact on the duration, cost, and quality of the final project is expected to facilitate the prevention of unsuccessful performance of construction contracts. The novelty of this study is that after codifying the most common causes of construction contract claims derived from the extant literature, they are further investigated in terms of their probability of occurrence and the perceived impact they have on the project completion time, its total cost, and quality. Based on calculated relative importance indices from expert opinion, this paper proposes probability and severity of impact values for 39 common causes of claims in the construction industry. These can be applied to calculate their risk values for stakeholders in public construction contracts to plan mitigation measures of contractual claims. The findings show that the top five riskiest causes of contractual claims in the Greek construction industry are changes in quantities, work, or scope, design quality deficiencies or errors, payment delays, delays in work progress, and the financial failure of the contractor.

An inter- and transdisciplinary concept has been developed, focusing on the scaling of industrial circular construction using innovative compacted mineral mixtures (CMM) derived from various soil types (sand, silt, clay) and recycled mineral waste. The concept aims to accelerate the systemic transformation of the construction industry towards carbon neutrality by promoting the large-scale adoption and automation of CMM-based construction materials, which incorporate natural mineral components and recycled aggregates or industrial by-products. In close collaboration with international and domestic stakeholders in the construction sector, the concept explores the integration of various CMM-based construction methods for producing wall elements in conventional building construction. Leveraging a digital urban mining platform, the concept aims to standardize the production process and enable mass-scale production. The ultimate goal is to fully harness the potential of automated CMM-based wall elements as a fast, competitive, emission-free, and recyclable alternative to traditional masonry and concrete construction techniques. To achieve this objective, the concept draws upon the latest advances in soil mechanics, rheology, and automation and incorporates open-source digital platform technologies to enhance data accessibility, processing, and knowledge acquisition. This will bolster confidence in CMM-based technologies and facilitate their widespread adoption. The extraordinary transfer potential of this approach necessitates both basic and applied research. As such, the proposed transformative, inter- and transdisciplinary concept will be conducted and synthesized using a comprehensive, holistic, and transfer-oriented methodology.

This paper aims to present the method of producing visual media for communicating the Asinara Island National Park plan. These products are landscape visualizations able to foster landscape preservation both from the point of view of the management of the landscape and of the citizen's involvement in the communication of the historical and environmental values of the landscape. Starting from landscape information gathering, the research has experimented with an operative method for processing different graphic representations from the same geographic database, calibrating the outputs to different audiences, their needs, objectives, and literacy skills. Three different types of products are presented: the first is a digital, dynamic and multisectoral decision-making GIS tool for park management. The second is a 3D model, aimed to the virtual fruition. The third is a map of the zoning park plan drawn to be easily readable to the non-expert public. This case study emerges as a replicable method to process the landscape information to make different visualization tools from a single geographic model, to meet the different requirements that arise from a complex landscape planning process.

New in vitro approaches for the assessment of their toxicity are crucial for creating better risk assessments given the growing use of nanoparticles (NPs) in the production of consumer goods. Humans will be exposed to nanoparticles through the inhalation route from contaminated aerosol. A promising method for evaluating the genotoxicity of NPs in vitro uses human airway epithelial cells. This study aimed to determine whether there were differences in morphology change of human bronchial/tracheal epithelial (HBTEC) cells responded to NPs in 2D and 3D spheroid models and to evaluate genotoxicity in 2D and 3D cultures after 24 hr exposure to TiO2-, Ag- and ZnO-NPs using the comet assay. Our 2D and 3D HBTEC cultures with TiO2-NPs did not show any statistically significant genotoxicity compared to controls for concentration points tested in vitro. HBTEC cells grown as 2D indicated that exposure to ZnO-NPs at low concentrations (10-50 ug/mL) for 24 hr did not cause any genotoxic effect but, at high concentrations, genotoxicity was observed. In contrast, treatment of 2D HBTEC with AgO-NPs led to an elevated in percentage of tail DNA damage from 50 ug/mL to 100 ug/mL, which was concentra-tion-dependent. Using 3D spheroid assays revealed a lower %tail length in ZnO- and AgO-NPs, thus exhibiting in vitro genotoxicity of NPs in this cell model. Spheroids (3D) rather than mono-layer cultures (2D) are believed to more precisely represent in vivo-like cell behavior when evaluating genotoxicity. Together, our findings demonstrate the genotoxic effects of NPs and point to the critical role that cell culture models play in the evaluation of toxicological risk.

In the production of green parts from powder, there is unavoidable slight deviation in the die filling, even when high-quality powders are used. The quantity of powder in the die varies and thus affects the weight of the compact. This filling variation results in variation of the pressing force, and thus influences the part geometry. The development of the DORST Netshape® System was conceived as an autonomous manufacturing system in order to compensate for these effects. Based on the Dorst Industry 4.0 innovations for part weight measuring immediately after pressing in combination with a laser dimension measuring system, this technology package attempts to reach enhanced precision and consistency in production. The paper presents results from various trials that show the capability of this new system, designed to improve the quality of pressed parts.

This paper presents the results of the investigation of composite sinters W-TiB2 which were used as an electrode in the process of electro-spark deposition (ESD) and the examination of the deposited layers. The scope of the study includes detailed characteristics of powder mixtures, composite sinters made using the spark plasma sintering method (SPS) and layers deposited in the electro-spark process. The ESD process, using the W+30 vol.% TiB2 electrode, was carried out using an automated device. The substrates were made of copper and aluminium. The topography analysis of the surfaces of the composite layer and the evaluation of their wear resistance properties are also presented. The analysis of the results of research showed the possibility to obtain, using the SPS method, composite materials of good quality, which can be used as electrodes in the ESD process. The obtained layers had increased wear resistance in relation to the substrate material.

We present progress in fast, high-resolution imaging, material classification, and fault detection using hyperspectral X-ray measurements. Classical X-ray CT approaches rely on data from many projection angles, resulting in long acquisition and reconstruction times. Additionally, conventional CT cannot distinguish between materials with similar densities. However, in additive manufacturing, the majority of materials used are known a priori. This knowledge allows to vastly reduce the data collected and increase the accuracy of fault detection. In this context, we propose an imaging method for non-destructive testing of materials based on the combination of spectral X-ray CT and discrete tomography. We explore the use of spectral X-ray attenuation models and measurements to recover the characteristic functions of materials in heterogeneous media with piece-wise uniform composition. We show by means of numerical simulation that using spectral measurements from a small number of angles, our approach can alleviate the typical deterioration of spatial resolution and the appearance of streaking artifacts.

Fatigue remains a challenge especially for high end metal AM parts and materials. From a design perspective, the fatigue limit of an AM solution can be improved upon by optimizing the manufacturing process for a certain material and part. In addition, improved accuracy of design methodologies aids in capturing the features critical for fatigue and quantifies their significance to desired part lifetime as well as providing a basis for their avoidance. In current work we present an overall concept merging thermomechanical process and powder bed solidification modeling to micromechanical analysis of fatigue of the resulting material microstructure. Material features critical to fatigue, particularly surface roughness, internal defects such as porosity and cracks and on the other hand inclusions, can be assessed directly on the basis of AM part microstructure with respect to the resulting fatigue limit. Case analyses consist of maraging steel and nickel alloys. The overall scheme provides a basis for optimization of metal AM solutions against fatigue and multiscale modeling founded basis for fatigue design.

Quality assurance has been one of the major challenges in laser-based additive manufacturing (AM) processes. This study proposes a novel process modeling methodology for layer-wise in-situ quality monitoring based on image series analysis. An image-based autoregressive (AR) model has been proposed based on the image registration function between consecutively observed thermal images. Image registration is used to extract melt pool location and orientation change between consecutive images, which contains sensing stability information. Subsequently, a Gaussian process model is used to characterize the spatial correlation within the error matrix. Finally, the extracted features from the aforementioned processes are jointly used for layer-wise quality monitoring. A case study of a thin wall fabrication by a Directed Laser Deposition (DLD) process is used to demonstrate the effectiveness of the proposed methodology.

Additive Manufacturing (AM) simplifies the fabrication of complex geometries. Its scope has rapidly expanded from the fabrication of pre-production visualization models to the manufacturing of end use parts driving the need for better part quality assurance in the additively manufactured parts. Machine learning (ML) is one of the promising techniques that can be used to achieve this goal. Current research in this field includes the use of supervised and unsupervised ML algorithms for quality control and prediction of mechanical properties of AM parts. This paper explores the applications of supervised learning algorithms - Support Vector Machines and Random Forests. Support vector machines provide high accuracy in classifying the data and is used to decide whether the final parts have the desired properties. Random Forests consist of an ensemble of decision trees capable of both classification and regression. This paper reviews the implementation of both algorithms and analyzes the research carried out on their applications in AM.

OBJECTIVE: Although 3D-printed anatomic models are not new to medicine, the high costs and lengthy production times entailed have limited their application. Our goal was developing a new and less costly 3D modeling method to depict organ-tumor relations at faster printing speeds. METHODS: We have devised a method of 3D modeling using DICOM images. Coordinates are extracted at a specified interval, connecting them to create mesh-work replicas. Adjacent constructs are depicted by density variations, showing anatomic targets (ie, tumors) in contrasting color. RESULTS: An array of organ solid-tumor models were printed via Fused Deposition Modeling 3D printer at significantly less cost ($0.05/cm3) and time expenditure (1.73 min/cm3; both, p<.001). Printed models helped promote visual appreciation of organ-tumor anatomy and adjacent tissues. Our mesh-work 3D thyroidal prototype reproduced glangular size/contour and tumor location, readily approximating the surgical specimen. CONCLUSIONS: This newly devised mesh-type 3D printing method may facilitate anatomic modeling for personalized care and improve patient awareness during informed surgical consent.

3D printing facilitates the straightforward construction of microchannels with complex three-dimensional architectures. Here, we demonstrate 3D-printed modular mixing components that operate on the basis of splitting and recombining fluid streams to decrease interstream diffusion length. These are compared to helical mixers that operate on the principle of chaotic advection.

It is time-consuming for acquiring complete data by fully phase encoding in two orthogonal directions along with one frequency encoding direction. Undersampling in the 3D k-space is promising in accelerating such 3D MRI process. Though 3D undersampling can be conducted according to predefined probability density, the density based method is not optimal. Because of the large amount of 3D data and computational cost, it is challenging to perform data-driven and learning-based 3D undersampling and subsequent 3D reconstruction. To tackle this challenge, this paper proposes a deep neural network called EEUR-Net, realized by optimizing specific undersampling patterns for the fully-sampled 3D k-space data. Innovatively, our undersampling algorithm employs an end-to-end deep learning approach to optimize phase encoding patterns and uses a 3D U-Net for image reconstruction of undersampled data. Through end-to-end training, we obtain an optimized 3D undersampling pattern, which significantly enhances the quality of the reconstructed image under the same acceleration factor. A series of experiments on a knee MRI dataset demonstrated that, in comparison to standard random uniform, radial, Poisson and equispaced Cartesian undersampling schemes, our end-to-end learned undersampling pattern considerably improves the reconstruction quality of undersampled MRI images.

Three-dimensional reconstruction plays an important role in assisting doctors and surgeons in diagnosing bone defects’ healing progress. Common three-dimensional reconstruction methods include surface and volume rendering. As the focus is on the shape of the bone, volume rendering is omitted. Many improvements have been made on surface rendering methods like Marching Cubes and Marching Tetrahedra, but not many on working towards real-time or near real-time surface rendering for large medical images, and studying the effects of different parameter settings for the improvements. Hence, in this study, an attempt towards near real-time surface rendering for large medical images is made. Different parameter values are experimented on to study their effect on reconstruction accuracy, reconstruction and rendering time, and the number of vertices and faces. The proposed improvement involving three-dimensional data smoothing with convolution kernel Gaussian size 0.5 and mesh simplification reduction factor of 0.1, is the best parameter value combination for achieving a good balance between high reconstruction accuracy, low total execution time, and a low number of vertices and faces. It has successfully increased the reconstruction accuracy by 0.0235%, decreased the total execution time by 69.81%, and decreased the number of vertices and faces by 86.57% and 86.61% respectively.

Solar3D is an open-source software application designed to interactively calculate solar irradiation at three-dimensional (3D) surfaces in a virtual environment constructed with combinations of 3D city models, digital elevation models (DEMs), digital surface models (DSMs) and feature layers. The GRASS GIS r.sun solar radiation model computes solar irradiation based on two-dimensional (2D) raster maps for given day, latitude, surface and atmospheric conditions. With the increasing availability of 3D city models and demand for solar energy, there is an urgent need for better tools to computes solar radiation directly with 3D city models. Solar3D extends GRASS GIS r.sun from 2D to 3D by feeding the model with input, including surface slope, aspect and time-resolved shading, that is derived directly from the 3D scene using computer graphics techniques. To summarize, Solar3D offers several new features which, as a whole, distinguish itself from existing 3D solar irradiation tools: (1) the ability to consume massive heterogeneous 3D city models, including massive 3D city models such as oblique airborne photogrammetry-based 3D city models (OAP3Ds or integrated meshes); (2) the ability to perform near real-time pointwise calculation for duration from daily to annual; (3) the ability to integrate and interactively explore large-scale heterogeneous geospatial data. (4) the ability to calculate solar irradiation at arbitrary surface positions including at rooftops, facades and the ground. Solar3D is publicly available at https://github.com/jian9695/Solar3D.

3D printing is described as the third industrial revolution: its impact is global in industry and progresses every day in society. It presents a huge potential for ecology and evolution, sciences with a long tradition of inventing and creating objects for research, education and outreach. Its general principle as an additive manufacturing technique is relatively easy to understand: objects are created by adding material layers on top of each other. Although this may seem very straightforward on paper, it is much harder in the real world. Specific knowledge is indeed needed to successfully turn an idea into a real object, because of technical choices and limitations at each step of the implementation. This article aims at helping scientists to jump in the 3D printing revolution, by offering a hands-on guide to current 3D printing technology. We first give a brief overview of uses of 3D printing in ecology and evolution, then review the whole process of object creation, split into three steps: (1) obtaining the digital 3D model of the object of interest, (2) choosing the 3D printing technology and material best adapted to the requirements of its intended use, (3) pre- and post-processing the 3D object. We compare the main technologies available and their pros and cons according to the features and the use of the object to be printed. We give specific and key details in appendices, based on examples in ecology and evolution.

Productivity has been modest in construction due to many reasons, especially project-specific operations and fragmentation. The main aim of this research is to map the challenges towards industrialization in construction through a comparative study of the manufacturing industry. An inductive approach and a qualitative method are followed by applying semi-structured inter-views, and node-based thematic analysis. The key elements of industrialization in mature man-ufacturing companies are benchmarked. The findings indicate a specific order of steps for indus-trialization in construction. Data and information management with achieved systematization have been sources of productivity in manufacturing companies. However, the systematization starts from the offering, construction companies need to define their offering, that is the products, and define their respective data. Only accurate and good quality data on products enables the systematization of order delivery processes, which are the engine for a company’s success or failure. Continuous efficiency improvement is only possible with systematized processes and respective data related to the processes. The originality involves clarifying the industrialization of construction companies via products, respective data, and processes considering industrialized manufacturing companies.

This study addresses the critical issue of dowel-bearing strength in Bambusa blumeana, a key sus-tainable construction material crucial for climate change mitigation. Given the lack of bamboo connection standards, the research focuses on determining the dowel-bearing strength of Bambusa blumeana, emphasizing factors such as dowel diameter, node placements, and the physical prop-erties of bamboo. A predictive equation is derived, enhancing the practicality of bamboo in struc-tural design. The results underscore a notable correlation between dowel diameter and character-istic strength, with implications for engineering practices. Node placements significantly affect dowel-bearing capacity, while bamboo's physical attributes, including thickness, culm diameter, and moisture content, exhibit modest correlations with strength. The derived equation aims to assist in structural design, mitigating splitting and bearing failures in bamboo structures. This research establishes a foundation for optimizing the use of Bambusa blumeana in sustainable construction, advancing the understanding of its dowel-bearing strength for improved sustainability and resili-ence in the construction industry. Future research suggestions include exploring bamboo-mortar composites, additional node placements, and employing more comprehensive empirical equations and curve-fitting techniques. The study advocates for further investigations with more diverse and larger bamboo samples to bolster robustness. Additionally, delving into bamboo ductility may offer valuable insights.

The accumulation of brown algae from the genus Sargassum has been increasing over the years in coastal regions of the Caribbean, Africa, Brazil, and Mexico. This causes harmful effects to the ecosystem, health, economy, and climate due to gas emissions from its decomposition process. There is the possibility of this biomass being reused in civil construction, and few studies have been carried out on its application to common Portland cement mortar. As such, the objective of this study is to evaluate the potential of sargassum ash as a mineral addition to partial replacement of fine aggregates in Portland cement mortar. Characterizations of the raw materials were carried out through X-ray fluorescence spectroscopy, loss on ignition, particle size distribution, Brunauer–Emmett–Teller (BET), real density, X-ray diffraction, scanning electron microscopy, and dispersion spectroscopy of electrons. The mortars were prepared by partially replacing the fine aggregate (sand) with sargassum ash, at 0%, 5%, 10% and 20%. Mortar performance was evaluated through water absorption, apparent porosity, apparent specific mass, compressive strength after 7, 28, and 63 days after curing. Lastly, a life cycle assessment in accordance with ISO standards 14040:2006 and 14044:2006. The results showed that replacing sand with sargassum ash increases water absorption, apparent porosity, and decreases the apparent specific mass and compressive strength as replacement increases. Nevertheless, the compressive strength results after 63 days, for 5 and 10% replacement did not differ statistically from reference values. The life cycle assessment indicates that mortars with partial replacement of sand by sargassum ash showed positive environmental impacts when compared to reference values for most categories regardless of the scenario analyzed, especially for mortar with 10% replacement. As such, the use of sargassum ash at 10% does not alter compressive strength values after 63 days while reducing its environmental impact. The application of this biomass in civil construction materials provides a destination for this algae that has been causing several social, environmental, and economic problems.

Earth is a complex material with a mechanical and physical behavior that differs from modern building materials. The conservation of rammed earth (RE) constructions presents specific difficulties that are challenging to overcome. The lack of knowledge about RE due to its abandonment for decades and attempts to adopt materials and repair methodologies designed for new building products has led to inadequate interventions. In the case of historic defensive constructions, the doubts and technical difficulties are even greater due to the nature of the so called military RE (with physical and mechanical characteristics significantly different from those of civil, more common, RE) and, not least, due to the historical and cultural heritage value of these constructions. Some important interventions have been carried out recently and others are underway or in the planning stage, and there is a constant lack of information and technical data on the best ways to intervene. To fill this gap, the state of conservation of the RE defensive structures and the results of interventions carried out throughout history in the southwest of the Iberian Peninsula are being assessed. This article sets out the framework of the subject, identifies the material and construction techniques, and recognizes the main causes of its deterioration and decay. With special focus on the most frequent damages detected in historic military defensive structures built with RE, it analyses and discuss the most common techniques that have been used for the repair and conservation of these particular structures.

Construction safety is especially important because the construction industry is so important to a country's development. Significant research and practice have been conducted to mitigate potential risks during construction and improve worker efficiency. With the rapid advancement of cognitive neuroscience and the incorporation of medical technology in recent years, various wearable monitoring devices have been widely used in the construction field for real-time monitoring of workers' physical and mental status. Among these, the use of EEG (Electroencephalogram) in construction environment research allows researchers to gain insight into the physical and mental states of construction workers while performing construction tasks. This review introduces EEG technology and portable EEG devices, followed by an overview of their use in both monitoring workers' adverse reactions and identifying hazards on construction sites, providing an effective guide for EEG research in the construction field and on-site safety management.

Development and redevelopment are important drivers of tree removal and canopy loss in urban landscapes. Local ordinances are often used to curtail tree removal, but punitive regulations alone may not be enough to reduce urban tree canopy loss in land development. In Florida (US), efforts to balance trees and development have so far focused on fees and fines, but with a recent backlash against tree regulations and the fast pace of urban growth, we explored the possible role of incentives in urban tree policies. We interviewed 20 land developers across Florida to understand their perspectives on current barriers and potential incentives for tree preservation and planting. We collected data from developers, whose perspectives on tree preservation are often unknown or overlooked, despite their significant role in tree planting, removal, and retention in and around cities. Our results show that major barriers to tree preservation and planting include requirements to grade sites for stormwater management, site constraints, and monetary costs. Most developers did not know of any existing incentives beyond intrinsic motivations but said that financial incentives would be most appealing to them. Top incentive suggestions include increasing building density, reducing impact fees and tax liability, and changing tree mitigation policies. Another promising finding is that developers are willing to work with regulators to find solutions that benefit both parties. Future research should consider evaluating the level of support and viability of different incentives by gathering feedback from policymakers, land developers, and the public.

The construction enterprise is a essential zone that contributes considerably to the worldwide financial system. but it faces numerous challenges, together with inefficiency in electric and electronics engineering tasks. This inefficiency results in delays, expanded charges, and decreased productivity. Device learning strategies have the capacity to deal with those challenges through optimizing the making plans and execution of electrical and electronics engineering tasks within the construction industry. This study paper targets to discover using machines gaining knowledge of strategies to maximise efficiency in electrical and electronics engineering projects inside the production industry. Mainly, the paper will be conscious of developing and imposing gadget mastering algorithms to optimize project scheduling, fabric procurement, and system utilization. The paper will even look at the ability of using predictive analytics to identify and mitigate dangers related to electric and electronics engineering tasks. The study could be based on a combination of literature review and empirical analysis. The literature evaluation will provide a top-level view of the demanding situations going through the development industry and the capability advantages of the usage of system getting to know strategies to deal with those challenges. The empirical evaluation will involve the improvement and testing of device mastering models on real-world information from electrical and electronics engineering initiatives inside the construction industry. The predicted results of this research are the development of a fixed of sensible recommendations for the use of machine gaining knowledge of strategies to optimize electric and electronics engineering projects within the construction industry. These suggestions will be beneficial for venture managers, engineers, and other stakeholders within the creation enterprise who're inquisitive about maximizing performance and decreasing charges of their tasks. Ordinary, this studies paper aims to contribute to the continued efforts to enhance the efficiency and productiveness of the development enterprise via exploring the ability of system studying techniques to optimize electrical and electronics engineering tasks.

The construction of earth buildings, both throughout history and in the current day, is well-established worldwide. Despite New Zealand's pre- and post-colonial history of earth construction, earth buildings as residential homes have not been well-received or popularised throughout present-day New Zealand. This research aims to identify the reasons for this lack of awareness and to determine methods that promote earth buildings in New Zealand. This research is based on data collected from semi-structured interviews conducted with subject matter experts and via an online questionnaire completed by members of the Earth Building Association New Zealand (EBANZ). The data collected revealed the experiences and perceptions of all participants regarding the advantages, challenges and promotion of earth buildings specific to New Zealand. Upon analysing these responses, key reoccurring themes were identified and compared. Regarding New Zealand's lack of awareness of earth buildings, interview and questionnaire participants responded that this shortcoming was due to earth construction being a very niche market and lacking commercial marketing. Education was the most frequently reoccurring theme raised by all participants as the top promotional tool for raising awareness of earth buildings. The results of this research can be applied to future work regarding obstacles that limit the growth of New Zealand's earth building industry, as well as research on the role of New Zealand's education system in exposing the next generation of builders, designers, and consumers to earth construction.

Progressive technologies and practices are shifting the possibilities of building design and improving work efficiency. Constantly changing site conditions require different procedures and designs that take into account these changing conditions, whether it is a design solution, a change in environmental conditions, or just sustainability factors. Adaptive building design offers opportunities to cope with changing factors to achieve the highest possible level of building quality. This case study deals with the topic of adaptive formwork design for building renovation, taking into account sustainability. Aim of the article is an investigation and demonstration of the building information modelling (BIM) environment used for the adaptive design of formwork elements for the building renovation in the context of sustainability. The object of the case study is a building in the center of Kosice, Slovakia. BIM environment allows prompt and correct adaptation of the formwork design to changing conditions of lighting, ventilation, heating and temperature during the design of the building.

In 2007, the excavation of the M-30 ring road located in Madrid and the creation of a green corridor either side of the Manzanares river brought significant change to the metropolitan area. The corridor and linear park which it provided were designed to contribute to the regeneration of the fluvial ecosystem, establish links among residents on each side of the river and promote cultural and leisure activities. This paper provides a sustainability analysis of the excavation of the M-30 (involving the socio-economic and environmental impact) 14 years after its construction. In order to show such an impact, an analysis of the area both prior to the project and after completion, as well as a hypothetical solution that uses improved materials, has been performed. This entails use of the multi-criteria decision-making model named MIVES (initials in Spanish, modelo integrado de valor para una evaluación sostenible). The MIVES method is based on the application of value functions of sustainability indicators selected by socio-economic and environmental criteria, chosen by experts. Results from analysis showed that the excavation of the M-30 considerably improved the sustainability of the area (sustainable index 3.43 and 6.26 both before and after the excavation works). However, use of improved materials in contrast with the application of conventional materials slightly improved the sustainability of the work (Sustainability Index 6.26 and 6.74, respectively, of the conventional materials).

The lean supply chain of construction engineering projects is to achieve the maximum satisfaction of the owners' needs in order to effectively achieve the goal of supply chain management. This paper explores an effective method of lean supply chain cost management for construction engineering projects with target cost management, so that each participating unit on the supply chain node can fully utilizes its core competencies to minimize internal consumption and waste, and achieve the optimal overall efficiency of the supply chain. According to the requirements of the goal planning theory of the construction project company, establish a lean supply chain cost planning system for the construction project, realize the basic model of the lean supply chain cost management of the construction project, and set the target cost from the lean project of the construction project. The technical decomposition is established by the process of cost decomposition and cost pressure transmission and sub-target cost planning.