Doubly Fed Induction Generator (DFIG) has a stator winding directly coupled with grid. Whereas, rotor winding is connected via a fault-prone back to back power converters. DFIG is known to be vulnerable to the grid faults. In early times, when a fault occurred, these generators were required to disconnect from the grid to secure the generator and power converters. However, due to the increased penetration of wind turbines into the power system, grid operators demanded that the wind turbines remain connected to the grid, as disconnecting them would further disrupt the grid. When a fault at the grid terminal occur, a high stator current is induced which further result in high rotor current. This current will trigger the DC-link voltage to rise. This high currents and DC-link voltage will cause harm to the converters. Thus, in this paper work, the crowbar protection system is employed for protecting the converters against excess energy. Furthermore, the analysis of DFIG is rendered by integrating the crowbar protection with the Battery Energy Storage System (BESS) for a much effective outcome in enhancing machine to drive the fault. MATLAB-Simulink software is used for modeling and simulation. All system parameters are obtained from ADAMA-II Wind Farm.

The paper presents dynamic and transient behaviour of the Doubly Fed Induction Generator (DFIG) in the wind farms. When Voltage sag or any faults occurs in the network, the variables in the doubly Fed Induction Generators are varying severely. If the voltage sag occurs, Active and Reactive power that generated by the DFIG will decrease and will increase respectively, The DC voltage link will be bigger, and the rotor current will increase. The DFIG in the wind farms uses Proportional Integral controller for controlling of electronic devices (Rotor Side Converter and Grid Side Converter). Even though the model of Doubly Fed Induction Generators and electronic device in the paper are linear, The Proportional Integral controllers cannot protect and control the variables. So, the power electronic converters and the DC-link can damage due to over voltages and over currents. Doubly Fed Induction Generator in the wind farm is simulated in MATLAB software. The results of the simulation present over voltage and over current in the DC-link and in the rotor of the Doubly Fed Induction Generator. In addition, it will explore the effect of Proportional Integral controller in Doubly Fed Induction Generator when three-phase short circuit fault occurs

In this paper, a novel voltage control strategy of stand-alone operation brushless doubly fed induction generator for variable speed constant frequency wind energy conversion systems was presented and discussed particularly. Based on the model of the generator power system, the proposed direct flux control strategy employs a nonlinear reduced-order generalized integrator based resonant sliding-mode control scheme to directly calculate and regulated the output value of converter which control winding stator required so as to eliminate the instantaneous errors of power winding stator flux, and no involving any synchronous rotating coordinate transformations. The stability, robustness and convergence capability of the proposed control strategy were described and analyzed. Owing to no extra current control loops involved, therefore simplifying the system configuration design and enhancing the transient performance. Constant converter switching frequency was achieved by using space vector pulse width modulation, which reduce the harmonic of generator terminal voltage. In addition, experimental results prove the feasibility and validity of the proposed scheme, and excellent steady and dynamic state performance is achieved.

The Doubly-Fed Induction Generator (DFIG) has significant features in comparison with Fixed Speed Wind Turbine (FSWT), which has popularized its application in power system. Due to partial rated back-to-back converters in the DFIG, Fault Ride-Through (FRT) capability improvement is one of the great subjects regarding new grid code requirements. To enhance the FRT capability of the DFIG, many studies have been carried out. Fault current limiting devices as one of the techniques are utilized to limit the current level and protect switches of the back-to-back converter from over-current damage. In this paper, a review is done based on fault current limiting characteristic of the proposed fault current limiting devices Therefore, Fault Current Limiters (FCLs) and Series Dynamic Braking Resistors (SDBRs) are mainly taken into account. Operation of all configurations including their advantages and disadvantages is explained. Impedance type and the fault current limiting devices’ location are two important factors, which significantly affect the DFIG behaviour in the fault condition. These two factors are basically studied by the simulation and their effects on the key parameters of the DFIG are investigated. Finally, future works in respect to the FCL application in the FRT improvement of the DFIG have also been discussed.

The main objective of this paper is to continue the development of activities of basic and applied research related to wind energy and to develop methods of optimal control to improve the performance and production of electrical energy from wind. A new control technique of Double fed induction generator for wind turbine is undertaken through a robust approach tagged nonlinear sliding mode control (SMC) with exponential reaching law control (ERL). The SMC with ERL proves to be capable of reducing the system chattering phenomenon as well as accelerating the approaching process. A nonlinear case numerical simulation test is employed to verify the superior performance of the ERL method over traditional power rate reaching strategy. Results obtained in Matlab/Simulink environment show that the SMC with ERL is more robust, prove excellent performance for the control unit by improving power quality and stability of wind turbine.

Experimental studies on the development of processes of obtaining ultradispersed metal-ceramic materials and coatings Mo-ZrO₂, Mo-Al₂O₃, W-ZrO₂, W-Al₂O₃ CVD by deposition from the gas phase in CO₂ process using low-temperature nonequilibrium plasma were carried out.The structure, microhardness, phase composition, and high-temperature annealing behavior of the materials were studied. It is shown that the choice of parameters of the deposition process and temperature annealing can be controlled by the distribution function of ultradispersed particles in the material and their sizes.High-temperature X-ray studies of "molecular" two-phase alloys Mo- Al₂O₃ and Mo- ZrO₂show that, depending on the elastic and thermal properties of the matrix materials and dispersed particles, the molybdenum matrix can be in an all-round tensed or all-round compressed state.In the study of the electro-physical characteristics of the two-phase disperse-strengthened alloys Mo- ZrO₂, Mo- Al₂O₃, W- ZrO₂, W- Al₂O₃ it has been established that in the region of temperatures 1023...1273K anomalous changes of specific electrical resistance and instability of thermal eddy in magnitude are observed apparently connected with the presence of internal stresses in material caused by ultradisperse particles.Theoretical aspects of the problem of increasing the carriers density in nanocomposite materials are reviewedTheoretical analysis of the effect of the ensemble of microparticles on the change of electron density in ultradisperse metal-ceramic materials is carried out. It is shown that the average values of the electron density in the matrix with the introduction of 1% of particles with a radius of 50 A increase by more than two orders of magnitude.The possibilities of creating ultradisperse compositions using radiation-plasma methods are considered.

Doubly-fed induction generators (DFIG) find extensive application in variable-speed wind power plants, providing notable advantages such as cost-effectiveness, operational flexibility across varying speeds, and enhanced power quality. This research focuses on the control of DFIGs employed in variable-speed wind turbine configurations. A suitable mathematical model is chosen for representative systems following a comprehensive review of contemporary research. Subsequent analysis reveals the instability of the open-loop time response of the system. To address this instability, the initial approach involves the implementation of the conventional Model Predictive Controller (MPC). However, the outcomes indicate that this controller falls short of delivering satisfactory performance despite the enhanced stability. In the subsequent phase, efforts are made to mitigate the impact of wind input variability by utilizing the Kalman filter, given its effectiveness in handling high variability. Following this, a novel methodology is introduced, which combines nonlinear MPC with the Lyapunov function. This method is based on the nonlinear model of the system. By using the Lyapunov function in the nonlinear MPC structure, the stability of the designed controller is guaranteed. The simulation results conducted using MATLAB software show that the output variables of the modeled DFIG system achieve stability within a reasonable timeframe applying the input.

We design an asymmetric nonlinear optical nanoantenna composed of a dielectric nanodisk and an adjacent nanobar. The proposed composite structure made of AlGaAs exhibits resonant response at both the fundamental and doubled frequencies. Being driven by the strong magnetic dipole resonance at the pump wavelength and a high-quality mode at the harmonic wavelength, the efficient second-harmonic radiation is generated predominantly along the vertical directions under the normally incident plane-wave excitation.

Induction heating is a fast, reproducible, and efficient heating method used in various manufacturing processes. However, there is no established additive manufacturing (AM) process based on induction heating using wire as feedstock. This study investigates a novel approach to AM based on inductive heating, where a steel wire is melted and droplets are detached periodically using a two-winding induction coil. The process parameters and energy input into the droplets are characterized. The induction generator exhibits sluggish response to the excitation voltage, resulting in a lag in the coil current. The process is captured using a high-speed camera, revealing regular droplet formation and uniform size and shape when operated within an appropriate process window. Larger drops and increased spatter formation occur outside this window. The proposed method allows for the production of droplets with almost spherical shapes. Further analysis and characterization of droplet formation and energy input provide insights into process optimization and overall efficiency.

The article presents development of the more electric turbofan engine in distributed architecture with a design thrust in the range from 3 to 7.5 and from 7.5 to 30 kN for small and medium-sized unmanned aerial vehicles. The engine subsystems are considered as separate smart modules with a built-in control system, exchanging data via a digital channel with the central engine control and diagnostics unit. The key smart engine units are combined in the following subsystems: starter and turbine generators, oil pumps, actuator of guide vanes, fuel pumps, fuel metering unit, control and diagnostic unit. All pumps and guide vane actuator are electrically driven. Control and monitoring signals are transmitted via a digital bus. Functional and reliability analysis, technical configuration design of each subsystem are presented. Based on analysis of the architecture of distributed control system for gearbox-free more electric engine, different configurations of described subsystems are proposed.

The arrival of new developments in the field of power electronics circuit’s applications in power systems builds new control strategy to improve voltage quality for power grid by overcome interruptions. Wind energy resources are unconventional resources and get advanced problems to power grid when it is connected. Uncertainty of load sharing, peak energy management, climatic conditions, wind velocity and wind energy injected into power grid leads many of power quality problems on power grid based on the existing guidelines specified in IEC-61400 standard. This system plans efficient operation of DFIG to eliminate the voltage collapse and mismatch frequency to power grid. The DFIG connected diode rectifier and rotor side converter wind generator works as an Efficient Static Synchronous Compensator (E-SATCOM) for supplying the demand of reactive power for power grid to mitigate PQ problems. The benefit of using a combined controller was verified by simulink/Matlab and its simulated results used Doubly Fed Induction Generator (DFIG), wind Turbine. This simulation results gives good quality transient and stable state response to manage and support reactive power for both symmetrical and unsymmetrical faults in connection of grid codes to provide continuous quality of power supply, multiple wind generators are required for 140 bus power grid.

The article presents an induction generator connected to the power grid using the AC / DC / AC converter and LCL coupling filter. In the converter, both from the generator side and from the power grid side, three-level inverters were used. The algorithm realizing Pulse Width Modulation (PWM) in inverters has been simplified to the maximum. Control of the induction generator was based on the Direct Field Oriented Control (DFOC) method. At the same time, voltage control has been used for this solution. The MPPT algorithm has been extended to include the variable pitch range of the wind turbine blades. The active voltage balancing circuit has been used in the inverter DC voltage circuit. In the control system of the grid converter with an LCL filter, the number of measurements was limited to the measurement of power grid currents and voltages. Synchronization of control from the power grid side is ensured by the use of a PLL loop with the system of preliminary suppression of undesired harmonics (CDSC).

Unmanned aerial vehicles serving as air base stations (UAV-BSs) are used in telecommunications, when the network is overloaded or unavailable, providing access to users on the ground. Due to its dynamics of providing access to networks in different altitudes, the electromagnetic signal of UAVs suffers losses along the path, thus facing several problems related to transmission, such as: attenuation, fading and distortion. In this work is proposed a 3D positioning strategy for UAVs, taking into account height, coverage radius and flight energy efficiency. Results show that the proposed algorithm is able to position the UAVs in suboptimal locations, providing network access for mobile users, maximizing the number of connected devices in the UAV-BS and saving energy, thus obtaining better performance than the approaches conventional.

The Energy Performance of Buildings Directive 2010 calls for the Nearly Zero Energy Standard for new buildings from 2021 onwards: Buildings using “almost no energy” are powered by renewable sources or energy produced by the building itself. For residential buildings, this ambitious new standard has already been reached. But for other building types this goal is still far away. The potential of these buildings to meet a Nearly Zero Energy Standard was investigated by analyzing ten case studies representing non-residential buildings with different uses. The analysis shows that the primary characteristics common to critical building types are a dense building context with a very high degree of technical installation (such as hospital, research and laboratory buildings). The large primary energy demand of these types of buildings cannot be compensated by building and property-related energy generation including off-site renewables. If the future Nearly Zero Energy Standard were to be defined with lower requirements because of this, the state related properties of Bavaria suggest that the real potential energy savings available in at least 85% of all new buildings would be insufficiently exploited. Therefore, it would be useful to instead individualize the legal energy verification process for new buildings to distinguish critical building types such as laboratories and hospitals.

The population of Bifidobacterium spp in faecal samples from breast-fed and formula-fed infants were investigated and developed antibiogram. The common bacterial growth media such as Man Rogos Sharpe (MRS), Brain Heart Infusion (BHI), Luria Bertani (LB) broth and Bifidobacteria agar were evaluated by the enumeration of Bifidobacterium spp. in faecal material. The results demonstrated that the population of Bifidobacterium spp. in the faecal samples of breast-fed infants is numerically high and, low in formula-fed infants. Phylogenetic analysis of the 16S rRNA, (Xylose/Fructose-6-phosphate phosphoketolase) xfp, and RFLP map of Bifidobacteria isolates suggested a presence of possible new and different Bifidobacterium spp. The intensity of the reddish brown colour formed during the f6ppk (Fructose-6-phosphate phosphoketolase) assay confirms the presence of variable Bifidobacteria. The highest recovery and diversity of Bifidobacteria were obtained from Bifidobacteria agar media. Growth in various media resulted in the formation of small (SCV) and big colony variants (BCV). We understand that the various antibiotic minimum inhibitory concentration (MIC) values obtained by applying different media, growth conditions, after bile salt treatment, and at low pH can vary. This study concludes that the variation of microbiological conditions differentiating resistant and susceptible strains is influenced by the test conditions as well.

In this research paper an algorithm for the derivation of methods based on theorems and axioms of fuzzy logic is presented, analyzed and applied. This new proposed procedure generates fuzzy methods and evaluates the value of fuzzy propositions through fuzzy implication. The new implications of the family should satisfy a number of axioms. Also, we denote the conditions in order to satisfy the maximum number of axioms. Moreover, authors state and prove theorems focusing on fuzzy implication, observing the rule: the fuzzy function of fuzzy implication is strong and that lead to fuzzy negation. In addition, the optimal number of repetitions is calculated according to the expected truth value. The formulas produced are verified through the use of temperature and humidity values over a certain period of time and in a certain geographical area in Greece. The basic steps of the methodology are the fuzzification of the data given ​​using four membership degree functions and the application of the membership degrees of temperature and humidity values on a new type of fuzzy implication. Finally, we observed that the isosceles trapezium gave the best results and the type of fuzzy implication can be effectively applied.

Purpose: The purpose of this study is to further explore how e-loyalty and E-marketing influences E-trust and satisfy the demand by offering fresh perspectives based on research as well as emphasis on the factors influencing the E-trust such as culture as a mediator. This study not only contributed theoretically but also presented practical implementations. Design/methodology/approach: Online survey was used to obtain data by focusing the Hospitality sector (Hotel Industry) and verifying the conceptual framework. Data was collected in multiple time lags. Findings: Findings showed that the E-trust influenced by E-loyalty and E-Marketing. E-trust comes from the previous experiences, e-loyalty and e-marketing. Further, some trends such as culture influenced the e-trust. Research limitation/implications: The present study is quite suitable for those Researchers interested in learning more about the effects of E-loyalty and E-marketing on user E-trust and how to mitigate cultural influences can benefit from the current study. This research also has implications for those who wish to improve market allure and survival in digital world. This study focused on the hospitality sector (Hotel Industry) in China; however, the sector and geography could be altered to suit the needs of the study's participants. Practical implications: The present study delivers the practical guidelines which are quiet suitable for understanding the formation of E-loyalty, E-marketing, and E-trust through which specific E-marketing strategy can be designed to deal with the consumer’s E-loyalty and their expectations as per their Cultural perspective. At some particular regions/countries, cultural trends are more important than practical market. This research study practically showed that how culture changed the consumer set of mind. Originality/value: The relationship between E-loyalty, E-marketing, E-trust, specifically with the cultural influence in digital market has been the subject of few research.

This paper aims to study and analyze a new Peltier cell layout using a PCM in biphasic mode, with the liquid phase encapsulating the p-n junctions and the solid one playing the role of heat sink. The selected PCM is an organic compound that operates within a temperature range corresponding to the melting process. The phase change zone encompasses the working temperature of the Peltier cell, avoiding thermal gradient variation across the cell section and maintaining the operating conditions and the cell efficiency. PCM encapsulates the Peltier cell thermocouples, creating a layer that increases the power generation as the thickness reduces. We simulated the performance of the new configuration for different temperature gaps between both sides of the cell, obtaining an improvement in power generation from 1.65 to 7.93. This power increase ratio depends on the temperature gap and transient time to reach the steady working temperature. The control of the layer thickness, transient time, and working temperatures resides in the external heating power source, which varies the operating conditions regulating the heat power and the airflow. Maximum output power from the cell prototype is 36.5 W, while conventional Peltier cells operating in similar conditions produce 7.3 W, which represents a power gain of 500%.

Epistemological naturalism dismisses the notion that epistemology is a basis for the empirical sciences. In particular, it rejects the demand for a general justification of induction. Making inductive generalisations is a basic habit among humans. There is no such thing as a logic of inductive inference. The role of induction in science is heuristic; it is our way of inventing new theoretical predicates and developing theories. We discover new laws by applying inductive thinking; but this is not any kind of inference which can be evaluated as more or less rational.

This research emphasizes a meta-heuristic Modified Ant Lion Optimizer (MALO) optimization approach for simultaneous utilization of DSTATCOM devices and distributed Photovoltaic (PV) sources with network reconfiguration in a radial power distribution scheme. In a radial power distribution network with network reconfiguration majority of the research is based on Constant Power model analysis. However, it is noticed that load models have a substantial impact on the distributed PV sources and the D-STATCOM device's optimal size and position. The effect of the Constant Power (CP) and Polynomial (ZIP) with load growth load models for the simultaneous insertion of distributed PV sources and DSTATCOM devices with network reconfiguration examined in this research work for power system planning. The penetration levels of distributed PV sources considered for the investigation are 25%, 50%, 75%, and 100%. The principal objective of this research is to reduce network total power losses, enhance the voltage magnitude profile at all buses, and reduce the overall operating cost while adhering to equality and inequality constraints. The proposed algorithm verified on 118-node test systems. The investigation is carried out for planning network upgradation to a High Voltage Distribution System(HVDS) on 317 nodes in the rural Bangalore Electricity Supply Company Limited(BESCOM) radial distribution scheme. Simulated results obtained by this method are validated with the BAT algorithm and available techniques in the literature.

The validity of our universe as a three-dimensional space (3+1 in relativity) is considered a fundamental fact in physics. In this study, we show that our observed world is thus the output of a prior fundamental operator referred to as an organizer. The organizer is an expansion of projecting operators. It is been shown that identical weighted projecting operators, which are associated with identical particles, generate subspaces of entangled states, whereas groups of unequal weighted coefficients are responsible for finite-size subspaces that are associated with unidentical particles. Considering 3D-subspaces as evidence of the coefficients’ arrangement in our universe, we implement our formalism to describe the implacable vectors, location, momentum, and force within each 3D subspace. By implementing the Heisenberg relation, we drive both the classical and quantum expressions for the laws of motion.

Characterization of cancer cells and neural stem cells indicates that tumorigenicity and pluripotency are coupled cell properties determined by neural stemness, and tumorigenesis represents a process of progressive loss of original cell identity and gain of neural stemness. This reminds of a most fundamental process required for the development of the nervous system and body axis during embryogenesis, i.e., embryonic neural induction. Neural induction is that, in response to extracellular signals that are secreted by the Spemann-Mangold organizer in amphibians or the node in mammals and inhibit epidermal fate in ectoderm, the ectodermal cells lose their epidermal fate and assume the neural default fate and consequently, turn into neuroectodermal cells. They further differentiate into the nervous system and also some non-neural cells via interaction with adjacent tissues. Failure in neural induction leads to failure of embryogenesis, and ectopic neural induction due to ectopic organizer or node activity or activation of embryonic neural genes causes a formation of secondary body axis or a conjoined twin. During tumorigenesis, cells progressively lose their original cell identity and gain of neural stemness, and consequently, gain of tumorigenicity and pluripotency, due to various intra-/extracellular insults in cells of a postnatal animal. Tumorigenic cells can be induced to differentiation into normal cells and integrate into normal embryonic development within an embryo. However, they form tumors and cannot integrate into animal tissues/organs in a postnatal animal because of lack of embryonic inducing signals. Combination of studies of developmental and cancer biology indicates that neural induction drives embryogenesis in gastrulating embryos but a similar process drives tumorigenesis in a postnatal animal. Tumorigenicity is the manifestation of aberrant occurrence of pluripotent state in a postnatal animal. Pluripotency and tumorigenicity are both but different manifestations of neural stemness in pre- and postnatal stage, respectively, of animal life. The unique property of neural stemness is derived from the evolutionary advantage of neural genes and the neural-biased state of the last common unicellular ancestors of metazoan. Based on these findings, I discuss about some confusion in cancer research, propose to distinguish the causality and associations and discriminate causal and supporting factors involved in tumorigenesis, and suggest revisiting the focus of cancer research.

Considerable attention has been given to the research field of bioorganometallic chemistry, which is a hybrid chemistry field between biology and organometallic chemistry. The introduction of biomolecules, which have hydrogen bonding sites and chiral centers, into organometallic compounds is considered to be a promising strategy to construct chirality-organized bioorganometallic conjugates. This feature paper sketches an outline of induction of helical chirality into bioorganometallic conjugates. Topics covered include control of the helical chirality of 1,n’-disubstituted ferrocene moieties in ferrocene-dipeptide conjugates and the chirality induction of the Au(I)–Au(I) axis in the dinuclear organogold(I)-uracil conjugates.

The deployment of a Static Synchronous Compensator within a microgrid can facilitate voltage and reactive power regulation, leading to enhanced stability and reliability. Within a microgrid setting, a STATCOM can effectively balance power supply and demand, and mitigate voltage fluctuations caused by the intermittent nature of renewable energy sources. To ensure the successful integration of a STATCOM within a microgrid, coordinating the control system with other Distributed Energy Resources, especially when multiple control strategies are employed, can be a challenging task. Therefore, a meticulously designed control system is indispensable to guarantee the microgrid’s efficient and effective operation. The use of GA in LSTM tuning can accelerate the process of finding optimal hyperparameters for a specific task, obviating the necessity for time-consuming and computationally expensive grid search or manual tuning. This method can be particularly advantageous when handling large data sets and complex models. In this paper, an attempt has been made to model the STATCOM to communicate with the microgrid tuned using LSTM-GA for effective calculation of real and reactive power support during grid disturbances.

Fires are complex multi-physics problems that span wide spatial scale ranges. Capturing this complexity in computationally affordable numerical simulations for process studies and “outer-loop” techniques (e.g., optimization and uncertainty quantification) is a fundamental challenge in reacting flow research. Further complications arise for propagating fires where a priori knowledge of the fire spread rate and direction is typically not available. In such cases, static mesh refinement at all possible fire locations is a computationally inefficient approach to bridging the wide range of spatial scales relevant to fire behavior. In the present study, we address this challenge by incorporating adaptive mesh refinement (AMR) in fireFoam, an OpenFOAM solver for simulations of complex fire phenomena involving pyrolyzing solid surfaces. The AMR functionality in the extended solver, called fireDyMFoam, is load balanced, models gas, solid, and liquid phases, and allows us to dynamically track regions of interest, thus avoiding inefficient over-resolution of areas far from a propagating flame. We demonstrate the AMR capability and computational efficiency for fire spread on vertical panels, showing that the AMR solver reproduces results obtained using much larger statically refined meshes, but at a substantially reduced computational cost. We then leverage the computational efficiency of the AMR solver to demonstrate an optimization framework for fire suppression based on the open-source Dakota toolkit.

The study presents an efficient computational investigation on the behaviour of the direct-drive system integrated into the offshore 5MW NREL wind turbine model under demanding aerodynamic loading conditions with the aim of optimising and developing more sustainable key structural components. The research was based on computational simulation packages to verify the use of real-world wind data, the loading conditions on the blade structures through aero-elastic simulation studies, as well as analyse the behaviour of the drive system. Through the application of validated aerodynamic loading conditions, resulting normal forces on the blades structure were obtained and applied to a dedicated simplified model that was also previously validated, to estimate the transferred loads into the powertrain. The adopted methodology allowed for the identification of shaft misalignment induced air-gap eccentricity. The impact of shaft deflections on resulting magnetomotive force was considered by making use of the Maxwell stress distribution expression. By taking into account the resulting loading cases on the generator structure, as well as the inherent typical loads generated by the electrical machine, a procedure including structural parametric and topology optimisation was developed and performed, achieving a rotor mass reduction between 8.5 and 9.6% if compared with the original model.

The abilities of quantitative description of noise are restricted due to its origin and only the statistical and spectral analysis methods can be applied while an exact time evolution cannot be defined or predicted. It emphasizes the challenges faced in many applications including communication systems where noise can play, on one hand, a vital role impacting signal-to-noise ratio but possessing, on the other hand, unique properties such as infinite entropy (infinite information capacity), exponentially decaying correlation function and so on. Despite the deterministic nature of chaotic systems, the predictability of chaotic signals is limited for a short time window putting them close to random noise. In this article, we propose and experimentally verify an approach to achieve Gaussian-distributed chaotic signals by processing the outputs of chaotic systems. The mathematical criteria, on which the main idea of the study is based on, is the Central Limit Theorem which states that the sum of a large number of independent random variables with similar variances approaches a Gaussian distribution. The study involves more than 40 mostly three-dimensional continuous-time chaotic systems (Chua’s, Lorenz’s, Sprott’s, memristor-based, etc.) whose output signals are analyzed according to criteria that encompass the probability density functions of a chaotic signal itself and its envelope and phase, statistical and entropy-based metrics such as skewness, kurtosis, and entropy power. We found that two chaotic signals of Chua’s and Lorenz’s systems exhibited superior performance across the chosen metrics. Furthermore, our focus extended to determining the minimum number of independent chaotic signals necessary to yield a Gaussian-distributed combined signal. The analytic and experimental results indicate that the sum of at least three non-Gaussian chaotic signals closely approximates Gaussian distribution. It allows generation of reproducible Gaussian-distributed deterministic chaos by modeling simple chaotic systems.

Pistol shrimps generate cavitation bubbles. Cavitation impacts due to bubble collapses are harmful phenomena, as they cause severe damage to hydraulic machineries, such as pumps and valves. However, cavitation impacts can be utilized for mechanical surface treatment to improve the fatigue strength of metallic materials, which is called “cavitation peening”. Through conventional cavitation peening, a cavitation is generated by a submerged water jet, i.e., a cavitating jet or a pulsed laser. The fatigue strength of magnesium alloy when treated by the pulsed laser is larger than that of the jet. In order to drastically increase the processing efficiency of cavitation peening, the mechanism of pistol shrimp (specifically when used to create a cavitation bubble), i.e., alpheus randalli, was quantitatively investigated. It was found that a pulsed water jet generates a cavitation bubble when a shrimp snaps its claws. Furthermore, two types of cavitation generators were developed, namely, one that uses a pulsed laser and one that uses a piezo actuator, and this was achieved by mimicing a pistol shrimp.

Wearable thermoelectric generators (w-TEGs) convert thermal energy into electrical energy to realize self-powering of intelligent electronic devices, thus reducing the burden of battery replacement and charging, and improving the usage time and efficiency of electronic devices. Through finite element simulation, this study successfully designed high-performance thermoelectric generator and made it into wearable thermoelectric module by adopting “rigid device - flexible connection” method. It was found that higher convective heat transfer coefficient on cold-end leads to larger effective temperature difference and better power generation performance of device in typical wearable scenario. Meanwhile, at same convective heat transfer coefficient on the cold-end, longer TE leg length leads to larger temperature difference established at both ends of device, larger device output power and open-circuit voltage. However, when the convective heat transfer coefficient increases to a certain level, optimization effect of increasing TE leg length on device power generation performance will gradually diminish. For devices with fixed temperature difference between two ends, longer TE leg length leads to higher resistance of TEG, resulting in lower device output power but slight increase in open-circuit voltage. Finally, sixteen 16×4×2 mm2 TEGs (L=1.38 mm, W=0.6 mm) and two modules were fabricated and tested. At hot end temperature Th=33 ℃ and cold end temperature Tc=30 ℃, the actual maximum output power Pout of TEG is about 0.2 mW, and the actual maximum output power Pout of TEG module is about 1.602 mW, which is highly consistent with the simulated value. This work brings great convenience to research and development of wearable thermoelectric modules and provides new, environmentally friendly and efficient power solution for wearable devices.

Liquid propellants are fast becoming attractive for pulsed plasma thrusters due to their high efficiency and low contamination issues. However, the complete plasma interaction and acceleration processes are still not very clear. Present paper develops a multi-layer numerical model for liquid propellant PPTs. The model proposes a possible acceleration mechanism for liquid fed pulsed plasma thrusters and accurately predicts the propellant utilization capabilities and estimations for the fraction of propellant gas that is completely ionized and accelerated to high exit velocities. Validation of the numerical model and the assumptions on which the model is based on is achieved by comparing the experimental results from two different liquid-fed thrusters developed at the University of Tokyo. Results show 50% of liquid propellant injected is completely ionized and accelerated to high exit velocities (> 50Km/s), whereas, neutral gas contribute to only 7% of the total specific impulse and accelerated to low exit velocity (< 4Km/s). The model shows an accuracy up-to 92%. Optimization methods are briefly discussed to ensure efficient propellant utilization and performance. The model acts as a tool to understand the background physics and to optimize the performance for liquid-fed PPTs.

Radar transmit signal design is a critical factor for the radar performance. In this paper, we investigate the problem of radar signal waveform design under the small signal power conditions for detecting a doubly spread target, whose impulse response can be modeled as a random process, in a colored noise environment. The doubly spread target spans multiple range bins (range-spread) and its impulse response is time-varying due to fluctuation (hence also Doppler-spread), such that the target impulse response is both time-selective and frequency-selective. Instead of adopting the conventional assumption that the target is wide-sense stationary uncorrelated scattering,we assume that the target impulse response is both wide-sense stationary in range and in time to account for the possible correlation between the impulse responses corresponding to close range intervals. The locally most powerful detector, which is asymptotically optimal for small signal cases, is then derived for detecting such targets. The signal waveform is optimized to maximizing the detection performance of the detector or equivalently maximizing the Kullback-Leibler divergence. Numerical simulations validate the effectiveness of the proposed waveform design for the small signal power conditions and performance of optimum waveform design are shown in comparison to the frequency modulated waveform.

This work focuses on the research area of energy generation and harvesting for its transformation into electrical energy with the primary use of energy independent sensor systems in the power range P=10-10000W. These systems are applied in sensing quantities in the transport sector (bridge structures, transport infrastructure, and the others ). The proposed theoretical harvester models describing the transformation of motion energy into electrical energy, also provides theoretical and experimental models. Results obtained in the design and construction of a robust motion generator with primarily linear geometry system technology are presented. The expected output electrical power of the harvester is variable and is designed based on the linear motion generated by the engine- compressed air, small fuel system, etc. The fundamental design of the generator core has been continuously numerically modeled and an experimental setup has been developed to analyze specific parts and variations in order to validate the concept and achieve the most suitable parameters with the selected construction materials. A scaled down version of the model principle was tested in experiments and then the parameters and results were compared with the predicted theoretical analyses.

The increased interest in space activities, structural health monitoring, and terrestrial monitoring in hostile and inaccessible zones places a high demand for energy sources for autonomous systems. Conventional electrochemical batteries that could be used are plagued by low energy storage density, short life, disposal of unwanted batteries, and related undesired recharging or replacement maintenance requirements, which endangers the environment. Fuel cells and solar energy sources being exploited to mitigate the adverse effect of environmental threats posed by batteries and fossil fuels are costly to acquire and maintain. The availability of energy sources derived from waste heat from radioactive decay for domestic appliances and industrial equipment will also help alleviate the effects of climate change, which continues to threaten the environment due to fossil fuel energy-based sources that emit harmful carbon monoxide into the atmosphere. A combination of energy from waste heat, harvested via thermoelectricity and existing battery technology to produce a hybrid energy source, can guarantee secured energy for an extended period. Based on the Seebeck effect, thermoelectric energy generation may considerably contribute to sustainable energy development and meet the power demand for spacecraft applications. Modeling of the energy from waste heat, the Li-ion battery, and a hybrid energy source are considered, and their performances are established using the MATLAB/Simulink environment. Results confirmed the comparative advantage of the hybrid energy source over and above the respective electrochemical batteries and waste heat energy sources regarding effectiveness and performance efficiency. Since batteries are required to operate in a constantly changing environment, the effects of temperatures on batteries were investigated. The results show that the performances of batteries decrease with a decrease in ambient temperature and that the higher the maximum operating capacity, the higher the battery's internal temperature.

This paper presents PrognosEase; a software that provides an easier way to produce different types of run-to-failure data mimicking real-world conditions to simplify prognosis studies in terms of data collection and improvement in ML degradation modelling process. Different types of degradation types made available to meet different types of applications. Besides, some primary ML tests were performed to ensure that complexity patterns of real systems could be observed in the training/testing predictions attitude. This paper also presents the impacts, limitations and potential improvements of the data generator.

Background: We previously developed a refined, tumor selective adenovirus, Ad5NULL-A20, har-boring tropism ablating mutations in each major capsid protein, to ablate all native means of infection. We incorporated a 20mer peptide (A20) in the fiber knob for selective infection via αvβ6 integrin, a marker of aggressive epithelial cancers. Methods: To ascertain the selectivity of Ad5NULL-A20 for αvβ6 positive tumor cell lines of pancreatic and breast cancer origin, we performed reporter gene and cell viability assays. Biodistribution of viral vectors in mice harboring xenografts with low, medium, and high αvβ6 levels was quantified by qPCR for viral genomes 48 hours post intravenous administration. Results: Ad5NULL-A20 vector transduced cells in an αvβ6 selective manner, whilst cell killing me-diated by oncolytic Ad5NULL-A20 was αvβ6 selective. Biodistribution analysis following intrave-nous administration into mice bearing breast cancer xenografts demonstrated that Ad5NULL-A20 resulted in significantly reduced liver accumulation coupled with increased tumor accumulation compared to Ad5 in all three models, with tumor: liver ratios improved as a function of αvβ6 expression. Conclusions: Ad5NULL-A20 based virotherapies efficiently target αvβ6 integrin positive tumors following intravenous administration, validating the potential of Ad5NULL-A20 for systemic ap-plications, enabling tumor selective overexpression of virally encoded therapeutic transgenes.

Dynamic phase modulation is vital for tunable focusing, beaming, polarization conversion and holography. However, it remains challenging to achieve full 360∘ dynamic phase modulation while maintaining high reflectance or transmittance based on metamaterials or metasurfaces in the terahertz regime. Here we propose a doubly resonant graphene-metal hybrid metasurface to address this challenge. Simulation results show that by varying the graphene Fermi energy, the proposed metasurface with two shifting resonances is capable to provide dynamic phase modulation covering a range of 361∘ while maintaining relatively high reflectance above 20% at 1.05 THz. Based on the phase profile design, dynamically tunable beam steering and focusing are numerically demonstrated. We expect this work will advance the engineering of graphene metasurfaces for the dynamic manipulation of terahertz waves.

The main aim of this work is to report an alternative energy efficient technique of fabricating flexible thermoelectric generators (TEGs) using printable ink. In this process, we have fabricated thermoelectric (TE) composite thick film and we are experimenting several ways to overcome the challenges of conventional and additive manufacturing methods. Two different mesh sizes of n-type bismuth particle, various binder to thermoelectric (TE) material weight ratio, and two different pressure (200 MPa and 300 MPa) were employed for optimizing the thermoelectric properties of TE composite films. We are also exploring naturally occurring chitosan as a binder. Dimethyl sulfoxide (DMSO) dissolved chitosan was used for the binder and less than 0.2 wt% of chitosan was sufficient for the fabrication of TE inks and composite films. Low energy intensive curing process was employed to evaporate the solvent from the drop casted inks. External uniaxial pressure not only eliminated high energy intensive curing processes but also increased the packing density of the film by removing pores and voids in the chitosan-bismuth composite film. The microstructure analysis reveals that bulk-like structure, which rarely has voids, pores and grain boundaries, was observed in the composite films pressed at sufficiently high pressures. The highest performing composite film was obtained with the conditions of 1:2000 binder to bismuth weight ratio, 100 mesh of particle size, and 300 MPa of pressure. The best performing bismuth chitosan composite film pressed at 300 MPa had the power factor as 4009 ± 391 μW/m·K² with high electrical conductivity value of 7337 ± 522 S/cm. The measured thermal conductivity of the best performing chitosan-bismuth composite film was 4.4 ± 0.7 W/m·K and the figure of merit calculated from the thermal conductivity was 0.27 at room temperature.

The growing attention for plug-in electric vehicles, and the associated high-performance demands, have initiated a development trend towards highly efficient and compact on-board battery chargers. These isolated ac-dc converters are most commonly realized using two conversion stages, combining a non-isolated power factor correction (PFC) rectifier with an isolated dc-dc converter. This, however, involves two loss stages and a relatively high component count, limiting the achievable efficiency and power density and resulting in high costs. In this paper a single-stage converter approach is analyzed to realize a single-phase ac-dc converter, combining all functionalities into one conversion stage and thus enabling a cost-effective efficiency and power density increase. The converter topology consists of a quasi-lossless synchronous rectifier followed by an isolated dual active bridge (DAB) dc-dc converter, putting a small filter capacitor in between. To show the performance potential of this bidirectional, isolated ac-dc converter, a comprehensive design procedure and multi-objective optimization with respect to efficiency and power density is presented, using detailed loss and volume models. The models and procedures are verified by a 3.7 kW hardware demonstrator, interfacing a 400 V dc-bus with the single-phase 230 V, 50 Hz utility grid. Measurement results indicate a state-of-the-art efficiency of 96.1% and power density of 2.2 kW/dm³, confirming the competitiveness of the investigated single-stage DAB ac-dc converter.

An original approach has been proposed for designing a nanofibrous (NFs) layer using UV-cured polyvinylpyrrolidone (PVP) as a matrix, incorporating mesoporous graphene carbon (MGC) nanopowder both inside and outside the fibres, creating a sandwich-like structure. This architecture is intended to selectively adsorb and detect acetic acid vapours, which are known to cause health issues in exposed workers. The nanocomposite MGC-PVP-NFs layer was fabricated through electrospinning deposition onto interdigitated microelectrodes (IDEs) and stabilised under UV-light irradiation. To enhance the adhesion of MGC onto the surface of the nanocomposite polymeric fibres, the layer was dipped in a suspension of polyethylenimine (PEI) and MGC. The resulting structure demonstrated promising electrical and sensing properties, including rapid responses, high sensitivity, good linearity, reversibility, repeatability, and selectivity towards acetic acid vapours. Initial testing was conducted in a laboratory using a bench electrometer, followed by validation in a portable sensing device based on consumer electronic components (by ARDUINO®). This portable system was designed to provide a compact, cost-effective solution with high sensing capabilities. Under room temperature and ambient air conditions, both laboratory and portable tests exhibited favourable linear responses, with detection limits of 0.16 and 1 ppm, respectively.

The fundamental mechanism underlying negative-ion catalysis involves bond-strength breaking in the transition state (TS). Doubly-charged atomic/molecular anions are proposed as novel dynamic tunable catalysts and demonstrated in water oxidation to peroxide. Density Functional Theory TS calculations have found tunable energy activation barrier reduction ranging from 0.030 eV to 2.070eV, with Si²ˉ, Pu²ˉ, Pa²ˉ and Sn²ˉ the best catalysts; the radioactive elements usher in new application opportunities. C₆₀²ˉ reduces significantly the standard C₆₀ˉ TS energy barrier while graphene increases it, behaving like cationic systems. Rank-ordered catalysts according to their reaction barrier reduction efficiency, variation across charge states and systems reveal their tunable and wide applications, ranging from water purification to biocompatible anti-viral and anti-bacterial sanitation systems.

Europium is the most-studied and least-well-understood rare earth ion (REI) dopant in GaN. While attempting to increase the efficiency of red GaN light-emitting diodes (LEDs) by implanting Eu⁺ into p-type GaN templates, the Strathclyde University group, in collaboration with IST Lisbon and Unipress Warsaw, discovered hysteretic photochromic switching (HPS) in the photoluminescence spectrum of doubly doped GaN(Mg):Eu. Our recent work, summarised in this contribution, has used time-, temperature- and light-induced changes in the Eu intra-4f shell emission spectrum to deduce the microscopic nature of the Mg-Eu defects that form in this material. As well as shedding light on the Mg acceptor in GaN, we propose a possible role for these emission centres in quantum information and computing.

Nowadays the practice of developing algorithms to maintain the confidentiality of data shows that there is a lack of some features, such as velocity, predictability, etc. Generating pseudorandom numbers is one such problem that lies in the basement of many algorithms, even in hardware microprograms. An unreliable generator can cause cyberattacks on it, despite the security in the upper layers. At the same time, the algorithm should be fast enough to provide uninterrupted circuit work for the entire system. The paper presents a new algorithm generating pseudorandom numbers on cellular automata, which is not only fast and easy-repeating, but unpredictable enough and can be used in cryptographic systems. Using the NIST statistical test suite for random and pseudorandom number generators (PRNG), it is shown that the presented algorithm is more than three times superior to the state-of-the-art methods and algorithms in terms of ? − ?????. A high level of the presented algorithm’s parallelization allows for implementation it effectively on calculators with parallel structure. CPU-based architecture, FPGA-based architecture, CUDA- based architecture of PRNG and different PRNG implementations are presented to confirm high performance of the proposed solution.

The novel Ionized Gas Thermoelectric Generator (IG-TEG) system that has been studied theoretically showing capabilities to continually extracting energy from the thermal energy of the ambient air, at low temperatures within the standard room temperature and below. This system does not need a temperature gradient in order to work, unlike the other TEGs that use Seebeck effect, and therefore this new system can be utilized for cooling purposes, by extracting energy instead of wasting energy in compressing the gas for cooling. This novel system was designed based on Static Ratchet Potential (SRP), which is known as a spatially asymmetric electric potential produced by an array of positive and negative electrodes. The ratchet potential produces electrical current from random Brownian Motion of charged particles that are driven by thermal energy. Ratchet potential was studied and investigated by several researches in the fields of sensing and energy harvesting. The main ratchet potential system parameter is the particles transportation, this parameter was studied under the condition of flashing ratchet potentials, and was analyzed based on several methods. In this study, a different approach is pursued to estimate particles transportation, by evaluating the charged particles distribution, and applying the other conditions of the SRP.

To generate a probability density function (PDF) for fitting probability distributions of real data, this study proposes a deep learning method which consists of two stages: (1) a training stage for estimating the cumulative distribution function (CDF) and (2) a performing stage for predicting the corresponding PDF. The CDFs of common probability distributions can be adopted as activation functions in the hidden layers of the proposed deep learning model for learning actual cumulative probabilities, and the differential equation of trained deep learning model can be used to estimate the PDF. To evaluate the proposed method, numerical experiments with single and mixed distributions are performed. The experimental results show that the values of both CDF and PDF can be precisely estimated by the proposed method.

The effects of ELICE16INDURES, a well-known plant conditioner developed by the Research Institute for Medicinal Plants and Herbs Ltd. Budakalasz, Hungary, were studied in a soybean population. The active ingredients of the compound have been selected to help elicit general immunity in plants without pathogenic damage, thereby roborizing the healthy plant population and preparing it for possible future biotic stressors. Here we have analyzed changes in the expression levels of genes encoding enzymes involved in the catalysis of metabolic pathways that induce and regulate PAMP-triggered immunity (PTI) at two different time points and treatments. Twenty-three different enzymes were analyzed that catalyze different metabolic pathways, such as the biosyntheses of jasmonic acid, salicylic acid, ethylene, phenylpropanoid, flavonoid, and phytoalexin biosynthesis and cellular detoxification processes. Bioinformatical softwares werw used to analyze the results. It has been found that some of the primary defense mechanisms (e.g., Mitogen-Activated-Protein Kinase (MAPK) cascade, jasmonic acid biosynthesis, flavonoid and phytoalexin biosynthesis, etc.) that intensify following the attack of pathogens can be activated without the intrusion of the actual pathogen by an immunochemical. Thus, we proved that plant resistance can be artificially conditioned.

Faraday's Law of induction is often stated as "a change in magnetic flux causes an EMF"; or, more cautiously, "a change in magnetic flux is associated with an EMF"; It is as well that the more cautious form exists, because the first "causes" form can be shown to be incompatible with the usual expression for EMF. This is not, however, to deny the causality as reasonably inferred from experimental observation ­ it is the equation for Faraday's Law of induction which does not represent the claimed cause-and-effect relationship. Here we investigate a selection of different approaches, trying to see how an explicitly causal mathematical equation, which attempts to encapsulate the "a change in magnetic flux causes ..." idea, might arise.

With the widespread use of electric machines there is a growing need to extract information from the machines to optimize their control systems and maintenance management. The present work shows the development of an embedded system to perform the monitoring of an squirrel cage induction motor rotor physical variables. The system comprises: circuit to acquire desirable rotor variable(s) value(s) and send it to the computer; a rectifier and power storage circuit that besides converting an alternating current in continuous also store energy for a certain amount of time to wait the motor engine shutdown; and magnetic generator that harvest energy from rotating field to power the circuits mentioned above. The embedded system is set on the rotor, making it difficult to power the system because it is rotating, problem solved with the construction of the magnetic generator eliminating the need of using batteries or collector rings and send data to the computer using a wireless NRF24L01 module. For the proposed system validation a temperature sensor (DS18b20) was used, variable known as the most important when identifying the need for maintenance and control systems. Tests were made getting satisfactory results proving the viability of using sensors on the rotor.

According to the World Health Organization, approximately 20 million people worldwide are infected annually with the hepatitis E virus (HEV). There are 4 main genotypes of HEV. Genotype 1 and genotype 2 are common in developing countries and are transmitted by contaminated water from a fecal-oral route. Genotype 3 and genotype 4 are common in developed countries and can lead to occasional transmission to humans by undercooked meat. Hepatitis E virus 1 and HEV3 can lead to fulminant hepatitis, and HEV3 can lead to chronic hepatitis and cirrhosis in immunocompromised patients. The majority of patients with HEV infection are asymptomatic and usually have spontaneous viral clearance without treatment. However, infection in immunocompromised individuals can lead to chronic HEV infection. Both acute and chronic HEV infections can have extrahepatic manifestations. No specific treatment is required for acute HEV infection, no treatment has been approved in chronic infection and no HEV vaccine has been approved by the (United States) Food and Drug Administration. This review focuses on the molecular virology (HEV life cycle, genotypes, model systems, zoonosis), pathogenesis, clinical manifestation, and treatment of chronic HEV infection, especially in immunocompromised patients, to provide clinicians a better understanding of the global distribution of these infections and the significant effect they can have on immunocompromised patients.

Considerable efforts have been made in recent years to identify an optimal treatment method for the removal of antibiotics from wastewaters. A series of supramolecular organic-inorganic magnetic composites containing Zn-modified MgAl LDHs and Cu-phthalocyanine as photosensitizer have been prepared with the scope to β-lactam antibiotics removal from aqueous solutions. The characterization of these materials confirmed the anchorage of Cu-phthalocyanine onto the edges of the LDH lamellae, with a negligible part inserted in the interlayer space. The removal of β-lactam antibiotics occurred via a concerted adsorption and photocatalytic degradation. The efficiency of the composites was depending on i) the LDH: magnetic nanoparticle (MP) ratio, that is strongly correlated to the textural properties of the catalysts, and ii) the phthalocyanine loading in the final composite. A maximum of the efficiency was achieved with a removal of ~93% of antibiotics after 2h of reaction.

Malignant pleural mesothelioma (MPM) has limited treatment options and poor prognosis. Frequent inactivation of the tumour suppressors BAP1, NF2 and P16 may differentially sensitise tumours to treatments. We have established chick chorioallantoic membrane (CAM) xenograft models of low-passage MPM cell lines and protocols for evaluating drug responses. Ten cell lines, representing the spectrum of histological subtypes and tumour suppressor status, were dual labelled for fluorescence/bioluminescence imaging and implanted on the CAM at E7. Bioluminescence was used to assess viability of primary tumours, which were excised at E14 for immunohistological staining or real-time PCR. All MPM cell lines engrafted efficiently forming vascularised nodules, however their size, morphology and interaction with chick cells varied. MPM phenotypes including local invasion, fibroblast recruitment, tumour angiogenesis and vascular remodelling were evident. Bioluminescence imaging could be used to reliably estimate tumour burden pre- and post-treatment, correlating with tumour weight and Ki-67 staining. In conclusion, MPM-CAM models recapitulate important features of the disease and are suitable to assess therapies using a broad range of MPM cell lines that allow histological or genetic stratification. They are amenable to multi-modal imaging, offering a time and cost-efficient, 3Rs-compliant alternative to rodent xenograft models to prioritise candidate compounds from in vitro studies.

This paper presents an algorithm for the fully automatic mesh generation for the finite element analysis of ships and offshore structures. The quality requirements on the mesh generator are imposed by the acceptance criteria of the classification societies as well as the need to avoid shear locking when using low degree shell elements. The meshing algorithm will be generating quadrilateral dominated meshes (consisting of quads and triangles) and the mesh quality requirements mandate that quadrilaterals with internal angles close to $90\degree$ are to be preferred. The geometry is described by a dictionary containing points, rods, surfaces and openings. The first part of the proposed method consist of an algorithm to automatically clean the geometry. The corrected geometry is then meshed by the frontal Delaunay mesh generator as implemented in the gmsh package. We present a heuristic method to precondition the cross field of the frontal quadrilateral mesher. Also the influence of the order in which the plates are meshed will be explored as a preconditioning step.

We talk about random when it is not possible to determine a pattern on the observed outcomes. A computer follows a sequence of fixed instructions to give any of its output, hence the difficulty of choosing numbers randomly from algorithmic approaches. However, some algorithms based on mathematical formulas like the Linear Congruential algorithm and the Lagged Fibonacci generator appear to produce "true" random sequences to anyone who does not know the secret initial input [1]. Up to now, we cannot rigorously answer the question on the randomness of prime numbers [2, page 1] and this highlights a connection between random number generator and the distribution of primes. From [3] and [4] one sees that it is quite naive to expect good random reproduction with prime numbers. We are, however, interested in the properties underlying the distribution of prime numbers, which emerge as sufficient or insufficient arguments to conclude a proof by contradiction which tends to show that prime numbers are not randomly distributed. To achieve this end, we use prime gap sequence variation. The algorithm that we produce makes possible to deduce, in the case of a binary choice, a uniform behavior in the individual consecutive occurrence of primes, and no uniformity trait when the occurrences are taken collectively.

Enterocins are bacteriocins synthesized by Enterococcus strains that show an interesting antimi-crobial effectiveness against foodborne pathogens such as Listeria monocytogenes. The objectives of this study were identify and analyze the expression of enterocin genes of Enterococcus isolated from breast-fed infants and evaluate the ability to inhibit three human isolates of virulent Lis-teria monocytogenes, as well as some probiotic bacteria. The susceptibility of the strains of L. mon-ocytogenes to fifteen antibiotics was tested, detecting resistance to cefoxitin (constitutive-ly resistant), oxacillin and clindamycin. Production of enterocins A, B and P were observed in Enterococcus faecium isolates, and enterocin AS-48 in an Enterococcus faecalis isolate. AS-48 showed antilisterial activity by itself, while the joint action of enterocins A and B, or B and P was neces-sary for inhibiting L. monocytogenes, demonstrating a synergistic effect of those combinations. The presence of multiple enterocin genes does not assured the inhibition of L. monocytogenes strains. However, the expression of multiple enterocin genes showed a good correlation with the inhibition capacity of these strains. Furthermore the potential beneficial strains of lactobacil-li and bifidobacteria examined were not inhibited by any of the enterocins produced individu-ally or in combination, with the exception of Bifidobacterium longum BB536, which was inhibited by enterocin AS-48 and the joint production of enterocins A and B or B and P. The enterocins studied here could be candidates for developing alternative treatments against antibi-otic-resistant bacterial infections. Moreover, these selected enterocin-producing E. faecium strains isolated from breast-fed infants could be used as probiotic strains due to their antilisterial effect as well as the absence of virulence factors.

The need for industrial and commercial machinery to maintain high torque while accurately following a variable angular speed is increasing. To meet this demand, induction motors (IMs) are commonly used with variable speed drives (VSDs) that employ a field-oriented control (FOC) scheme. Over the last thirty years, IMs have been replacing independent connection direct current motors due to their cost-effectiveness, reduced maintenance needs, and increased efficiency. However, IMs and VSDs exhibit nonlinear behavior, uncertainties, and disturbances. This paper proposes a robust combined adaptive passivity-based control (CAPBC) for this class of nonlinear systems that applies to angular rotor speed and stator current regulation inside an FOC scheme for IMs´ VSDs. It uses general Lyapunov-based design energy functions and adaptive laws with σ-modification to assure robustness after combining control and monitoring variables. Lyapunov’s second method and Barbalat Lemma prove that the control and identification error tends to be zero over time. Moreover, comparative experimental results with standard Proportional Integer controller (PIC) and direct APBC, show the proposed CAPBC effectiveness and robustness under normal and changing conditions

In this paper, we demonstrate the Collatz conjecture using the mathematical complete induction method. We show that this conjecture is satisfied for the first values of natural numbers, and in analyzing the sequence generated by odd numbers, we can deduce a formula for the general term of the Collatz sequence for any odd natural number n after several iterations. This formula is used in one case that we analyze using the mathematical complete induction method in the process of demonstrating the conjecture.

Callus induction of F. moluccana (sengon) was still an obstacle to indirect organogenesis regeneration. The purpose of the study was to determine the callus induction formation from root fragments of F. moluccana plantlets. Primary explants (fragments of roots) were cultivated on MS induction basal media and three concentration combination of PGRs (BAP and NAA): 0.5 ml/l BAP; 0,1 ml/l NAA (single PGR); and combination of 0.5 ml/l BAP + 0.1 ml/l NAA (double PGR). When roots were used as explants, high formation rates of callus (more than 70%) were obtained. Highest formation rates of callus were in NAA added at all clones (12 clones), then BAP added (7 clones) and BAP + NAA added (5 clones). The results indicated that BAP and NAA concentrations used in the media were influence the producing callus and affect the amount of callus produced from roots of sengon. The addition of NAA also gives higher callus proliferation results than the addition of BAP or the addition of a combination of the two hormones. The results indicated that BAP and NAA concentrations used in the media were influence the producing callus and affect the amount of callus produced from roots of sengon.

Aedes (Stegomyia) albopictus is a mosquito native to Southeast Asia. Currently, it has a wide distribution in America where natural infection with arboviruses of medical and veterinary importance has been reported. In spite of their importance in the transmission of endemic arbovirus, basic information of parameters affecting their vectorial capacity is poorly investigated. The aim of the work was to update the distribution range of Ae. albopictus in the Americas, review the blood-feeding patterns and compare the minimum infection rate (MIR) of the dengue virus (DENV) between studies of vertical and horizontal transmission. The current distribution of Ae. albopictus encompasses 21 countries in the Americas. Extensive review has been conducted for the blood-feeding patterns of Ae. albopictus. The results suggest that the mosquito is capable of feeding on 16 species of mammals and five species of avian. Humans, dogs, and rats are the most common host. Eight arboviruses with the potential to infect humans and animals have been isolated in Ae. albopictus. In the United States of America (USA), Eastern equine encephalitis virus, Keystone virus, La Crosse Virus, West Nile virus, and Cache Valley virus were isolated in the Asian mosquito. In Brazil, Mexico, Colombia, and Costa Rica, DENV (all serotypes) has been frequently identified in field-caught Ae. albopictus. Overall, the estimated MIR in Ae. albopictus infected with DENV is similar between horizontal (10.95) and vertical transmission (8.28). However, in vertical transmission, there is a difference in the MIR values if the DENV is identified from larvae or adults (males and females emerged from a collection of eggs or larvae). MIR estimated from larvae is 14.04 and in adults is 4.04. In conclusion, it has to be highlighted that Ae. albopictus is an invasive mosquito with wide phenotypic plasticity to adapt to broad and new areas, it is highly efficient to transmit the DENV horizontally and vertically, it can participate in the inter-endemic transmission of the dengue disease, and it can spread zoonotic arboviruses across forest and urban settings.

In this study, we propose an efficient field-free line (FFL) generator for mechanically driven FFL-magnetic particle imaging (MPI) applications. The novel FFL generator comprises pairs of Halbach arrays and bar magnets. The proposed design generates high-gradient FFLs with low-mass permanent magnets, realizing fine spatial resolutions in MPI. We investigate the generated magnetic field using simulations and experiments. Our results show that the FFL generator yields a high gradient of 4.76 T/m at a cylindrical field of view of 30 mm diameter and a 70 mm open bore. A spatial resolution of less than 3.5 mm was obtained in the mechanically driven FFL-MPI.

FPGA-based data acquisition and processing systems play an important role in modern high-speed, multichannel measurement systems, especially in High-Energy and Plasma Physics. Such FPGA-based systems require an extended control and diagnostics part corresponding to the complexity of the controlled system. Managing the complex structure of registers while keeping the tight coupling between hardware and software is a tedious and potentially error-prone process. Various existing solutions aimed at helping that task do not perfectly match all specific requirements of that application area. The paper presents a new solution based on the XML system description, facilitating the automated generation of the control system’s HDL code and software components and enabling easy integration with the control software. The emphasis is put on reusability, ease of maintenance in case of system modification, easy detection of mistakes, and the possibility of use in modern FPGAs. The presented system has been successfully used in data acquisition and preprocessing projects in High-Energy Physics experiments. It enables easy creation and modification of the control system definition and convenient access to the control and diagnostic blocks. The presented system is an open-source solution and may be adopted by the user for particular needs.

Information-theoretically provable unique true random numbers, which cannot be correlated or controlled by an attacker, can be generated based on quantum measurement of vacuum state and universal-hashing randomness extraction. Quantum entropy in the measurements decides the quality and security of the random number generator (RNG). At the same time, it directly determines the extraction ratio of true randomness from the raw data, in other words, it obviously affects quantum random bits generating rate. In this work, we commit to enhancing quantum entropy content in the vacuum noise based quantum RNG. We have taken into account main factors in this proposal to establish the theoretical model of quantum entropy content, including the effects of classical noise, the optimum dynamical analog-digital convertor (ADC) range, the local gain and the electronic gain of the homodyne system. We demonstrate that by amplifying the vacuum quantum noise, abundant quantum entropy is extractable in the step of post-processing even classical noise excursion, which may be deliberately induced by an eavesdropper, is large. Based on the discussion and the fact that the bandwidth of quantum vacuum noise is infinite, we propose large dynamical range and moderate TIA gain to pursue higher local oscillator (LO) amplification of vacuum quadrature and broader detection bandwidth in homodyne system. High true randomness extraction ratio together with high sampling rate is attainable. Experimentally, an extraction ratio of true randomness of 85.3% is achieved by finite enhancement of the laser power of the LO when classical noise excursions of the raw data is obvious.

Tribenuron-methyl is used extensively in Iranian cereal cropping systems under rainfed conditions. However, there is little information on the soil persistence and carryover of this herbicide and its phytotoxicity to subsequent crops in the rotation. This study was carried out with the aim of investigating the sensitivity of different chickpea cultivars to tribenuron-methyl and also finding alternative crops. In field experiments, the chickpea fields of Ravansar County, Kermanshah province, Iran were monitored during 2023-2022, and the growth of chickpea in response to residues of tribenuron-methyl used in the previous wheat crop was evaluated. Furthermore, in a greenhouse experiment, the effect of various concentrations of tribenuron-methyl on the growth of chickpeas, lentil and common vetch was investigated. In all the investigated species in this study, presence of tribenuron-methyl decreased plant growth. Ttotally, among examined crop species, lentil had a higher tolerance to tribenuron-methyl followed by common vetch and chickpea varieties. Bivanij chickpea variety was more sensitive to the residues of tribenuron-methyl in the soil (30% reduction in grain yield) when compared to the other two varieties, namely Mansour and Adel. Based on the results of this study, residues of tribenuron-methyl applied in wheat fields is the main responsible factor reducing the height of chickpea in rai-fed cropping systems of western Iran. It is recommended to replace lentil and common vetch with chickpeas in rotation with wheat in soils heavily contaminated with the residues of tribenuron-methyl.

This study aimed to investigate the efficacy of probiotics in elderly hospitalized tube-fed patients undergoing antibiotic therapy for Clostridium difficile-associated diarrhea (CDAD). Probiotics were administered to 29 patients, with twice-daily doses for 7 days following the completion of antibiotic treatment. In the probiotic group, while stool form showed no significant change, there was a significant decrease in stool frequency. Conversely, the control group exhibited improved stool form but not frequency. The probiotic group maintained a significant difference in stool form during the follow-up period. Additionally, the control group showed a positive correlation between stool form, frequency, antibiotic therapy, and intensive care unit admission, which was not observed in the probiotic group. These findings suggest that supplementing with probiotics can effectively normalize stool form in elderly hospitalized tube-fed patients undergoing antibiotic treatment for CDAD, highlighting the potential benefits of probiotic intervention in this specific population.

Dengue virus (DENV) is a member of the Flaviviridae family and is responsible for the most common mosquito-borne human disease. Currently, there are no available antiviral drugs to treat DENV infections. However, certain flavonoids, including baicalein and baicalin, have demon-strated significant anti-DENV effects in vitro. This study aimed to assess the bioavailability of baicalein and its metabolite, baicalin, in the blood serum of Albino Wistar rats using the LC/MS/MS method. The in vitro activity of sera obtained from rats administered baicalein was evaluated for its anti-DENV properties using quantitative RT-PCR and the Foci Forming Reduction Assay (FFRA). The results obtained through LC/MS/MS analysis indicated that the bioavailability of baicalin in rat blood serum reached 44.20 µg/ml one hour after oral administration of baicalein. Furthermore, the sera collected from rats given baicalein exhibited a significant 78.26% inhibition of DENV-2 replication when tested against Dengue-2 using both quantitative RT-PCR and FFRA. These findings suggest that baicalein and baicalin hold promise as potential therapeutic candidates for further investigation in the development of treatments against DENV infections.

Dementia is a rising public health concern. Feeding and nutritional problems increase as the disease progresses, affecting clinical course and caregiver burden. While some guidelines advise against percutaneous endoscopic gastrostomy (PEG) and tube feeding in advanced dementia, conflicting evidence exists. This study aims evaluating nutritional status and the influence of PEG-feeding on outcome and evolution of nutritional/progonosis markers of patients with severe dementia (PWSD) who underwent gastrostomy for nutritional support. We conducted a 16-year rectrospective study on 100 PEG-fed PWSD with strong familiar support. We evaluated survival PEG-feeding period, safety, and objective nutritional/progonosis data at the gastrostomy day and after 3 months: Body Mass Index (BMI), Mid Upper Arm Circumference, Tricipital Skinfold, Mid-Arm Muscle Circumference, albumin, transferrin, total cholesterol and hemoglobin. Most patients presented low values in these nutritional/progonosis parameters. No major life-threatening PEG complications were reported. The mean survival time after gastrostomy was 27.9 months (median of 17 months). Female sex, BMI recovery at 3 months, and higher baseline hemoglobin levels were associated with a reduced risk of death and increased survival time. The study concluded that, in carefully selected PWSD with strong familiar support, PEG feeding can improve nutritional status and have a positive impact on survival.

Inappropriate use of fertilizers is one of the major production constraints in sesame. Studies to optimize the use of N fertilizer on sesame were conducted at Humera Agricultural Research Center (HuARC) under rain fed and irrigation conditions. Thirteen (13) N doses were evaluated in a Randomized Complete Block Design (RCBD) during 2016, 2017 and 2018. In the rain fed condition; results showed higher number of days to 50% flowering on the higher N application. The 31-121.5 kg N ha-1 have scored higher seed yield, where the lower (18 kg N ha-1) and higher (156 kg N ha-1) N doses scored lower seed yield. In the irrigation condition; higher N application rate prolonged the flowering time to some extent and days to 90% maturity was reduced as N rate increased. Heavier seed weights and maximum seed yield were recorded on 64 and 75 kg N ha-1 and the lower N doses scored low seed yield. Agronomic efficiency of N fertilizer (N-AE) was higher on 64 kg N ha-1 under both growing conditions. The partial budget analysis revealed that 64 kg N ha-1 (rain fed) and 75 kg N ha-1 (irrigation) had the higher net profit, MRR and residual ranking. Therefore, for the greater sesame productivity 64 kg N ha-1 has to be recommended for rain fed and 64 to 75 kg N ha-1 for the irrigated sesame.

In 2020, students of Pakistan had to adapt to the online environment for the very first time. This study aims to analyze the perceptions of medical, dental, and allied health students about online education in Pakistan. A descriptive, cross-sectional study was done to assess the level of acceptance of undergraduate students. A pre-validated questionnaire regarding demographics, past-experience of e-learning, advantages disadvantages of e-learning, and general perception of students towards e-learning was distributed. Descriptive statistics were computed for demographics, Mann-Witney-U test was used to compare the differences of perceptions between pre-clinical year and clinical years students. Kruskal-Wallis test was applied to compare the results of three specialties of students. Chi-square was used to compare overall category-wise positive and negative responses of students. 1200 students participated in the study. The major advantage identified by all students was the ‘comfortable environment’ in which they studied online. The major disadvantage selected by preclinical year students was ‘anxiety due to social isolation’ and that chosen by clinical year students was ‘lack of patient interaction’. Overall, 72% of students had a negative perception of e-learning. Student-teacher training, student counselling sessions, and innovative techniques need to be introduced to enhance student engagement and reduce pandemic stress.

Oncogenic protein E6 from Human Papilloma Virus 16 (HPV-16) mediates the degradation of Membrane-associated guanylate kinase with inverted domain structure-1 (MAGI-1), throughout the interaction of its protein binding motif (PBM) with the Discs-large homologous regions 1 (PDZ1) domain of MAG1-1. Generic variation in the E6 gene that translates to changes in the protein’s amino acidic sequence modifies the interaction of E6 with the cellular protein MAGI-1. MAGI-1 is a scaffolding protein found at tight junctions of epithelial cells, where it interacts with a variety of proteins regulating signaling pathways. MAGI-1 is a multidomain protein containing two WW (rsp-domain-9), one guanylate kinase-like, and six PDZ domains. PDZ domains played an important role in the function of MAGI-1 and served as targets for several viral proteins including the HPV-16 E6. The aim of this work was to evaluate, with an in silico approach, employing molecular dynamics simulation and protein-protein docking, the interaction of the intragenic variants E-G350 (L83V), E-C188/G350 (E29Q/L83V), E-A176/G350 (D25N/L83V), E6-AAa (Q14H/H78Y/83V) y E6-AAc (Q14H/I27RH78Y/L83V) and E6-reference of HPV-16 with MAGI-1. We found that variants E-G350, E-C188/G350, E-A176/G350, AAa and AAc increase their affinity to our two models of MAGI-1 compared to E6-reference.

LSM4 is an essential yeast gene encoding a component of different LSM complexes involved in the regulation of mRNA splicing, stability and translation. In previous papers we reported that the expression in S. cerevisiae of the K. lactis Lsm4 gene lacking the C-terminal Q/N-rich domain in a Lsm4 null strain S. cerevisiae (Sclsm4D1) restored cell viability. Nevertheless, in this transformed strain we observed some phenotypes which are typical markers of regulated cell death, Reactive Oxygen Species and oxidated RNA accumulation. In this paper we report that a similar truncation operated in the S. cerevisiae LSM4 gene confers to cells the same phenotypes observed with the K.lactis LSM4D1 gene. Up to now there was no evidence on the direct involvement of LSM4 in autophagy. Here we found that the Sclsm4D1 mutant showed defects in the induction of autophagy and it was very sensitive to nitrogen starvation or treatment with low doses of rapamycin, an inducer of autophagy. Moreover, both during nitrogen starvation and ageing, the Sclsm4D1 mutant accumulated cytoplasmic autophagy-related structures, suggesting a role of Lsm4 in Phagophore Assembly Site (PAS) processing and/or vacuolar autophagosome internalization

In several mammalian species including humans, complex stimulation patterns such as cognitive challenge and physical exercise lead to improvements in organ function, organism health and performance, as well as possibly longer lifespans. The hypothesis is presented here that activity-dependent transcriptional programs, induced by these environmental stimuli, temporarily and lightly de-differentiate somatic cells such as neurons and muscle cells into a state that resembles functionally younger cells to allow cellular remodeling and adaptation of the organism to environmental change. This cellular adaptation program targets several process classes that are heavily implicated in aging, such as mitochondrial metabolism, cell-cell communication, intracellular signaling and epigenetic information processing and leads to functional improvements in these areas. I reverse engineer these activity-dependent gene programs, identify critical molecular nexus points such as CREB, MEF2 and cFos and speculate as to how one might leverage them to prevent and attenuate human aging-related decline of body function, enhance human performance and restore more youthful levels of function and morphology. The findings presented here can serve as a basis for the study and development of effective longevity efforts as the underlying gene programs could be used as markers for treatment success and as targets for therapy development.

A two element Multiple Input Multiple Output UWB (Ultra-wide band) antenna is presented in this paper. The antenna is backed by the FR-4 substrate with a thickness of 1.6 mm and dielectric constant of 4.3 covering an area of 52.8 × 29 mm2. The proposed MIMO antenna consists of two single UWB antennas and a stub placed between the two antennas to reduce the mutual coupling. The proposed antenna achieves the voltage standing wave ratio (VSWR) of less than 2 and more than 86% radiation efficiency over the whole band of interest. Performance of the antenna is examined using both simulation and experiment. The design exhibits good performance characteristics in terms of bandwidth, gain, efficiency, return loss and VSWR. The proposed antenna is analyzed using the CST Microwave Studio software. The prototype model of the antenna is fabricated, tested, and measured to validate the simulation return loss results. There is acceptable agreement between the measured and simulated results.

Increased sugar intake is implicated in Type-2 diabetes and fatty liver disease. Mechanisms by which glucose and fructose components promote these conditions are unclear. We hypothesize that alterations in intestinal metabolite and microbiota profiles specific to each monosaccharide are involved. Two groups of six adult C57BL/6 mice were fed for 10-weeks with a diet where either glucose or fructose was the sole carbohydrate component (G and F, respectively). A third group was fed with normal chow (N). Fecal metabolites were profiled every 2-weeks by ¹H NMR and microbial composition was analysed by real-time PCR (qPCR). Glucose tolerance was also periodically assessed. N, G and F mice had similar weight gains and glucose tolerance. Multivariate analysis of NMR profiles indicated that F mice were separated from both N and G, with decreased butyrate and glutamate and increased fructose, succinate, taurine, tyrosine and xylose. Compared to N and G, F mice showed a shift in microbe populations from gram-positive Lactobacillus spp. to gram-negative Enterobacteria species. Substitution of normal chow carbohydrate mixture by either pure glucose or fructose for 10 weeks did not alter adiposity or glucose tolerance. However, F G and N mice generated distinctive fecal metabolite signatures with incomplete fructose absorption as a dominant feature of F mice.

The paper describes and analyzes the performance of a new thermoelectric generation system based on the use of Peltier cells inserted in the ducts of the air conditioning equipment. The hot and cold air streams that flow in the two separated sections of an air conditioning system are used to create a thermal gradient between the two faces of the Peltier cells. Hot and cold air flow inside the A/C unit are driven to a built in thermal chamber where the Peltier cells are placed. Peltier cells are incrusted into an insulation wall that separates the two sections of the chamber through which hot and cold air streams are flowing. The so designed configuration allows the Peltier cells to generate electric current. The study has been run for constant cold air temperature and variable hot air temperature, resulting in a variable performance of the thermoelectric generator. Theoretical study has been completed with experimental tests to determine real performance of the thermoelectric unit. Efficiency of the thermoelectric generator has been found to be linearly dependent on the temperature difference between hot and cold air subsections of the chamber. Maximum efficiency, however, is limited by the hot air stream temperature, since in real conditions ambient temperature cannot overpasses a specific value. For standard operational conditions, 5º C and 45º C for the cold and hot air streams, the thermoelectric generator operates at 44% of the maximum efficiency attainable.

This paper provides a proof of concept for a linear electric generator that can be used to harvest energy from various sources of linear motion, such as vibrations, free-piston engines and wave energy. The generator can be used to power small electronic devices, such as sensors, or charge household batteries. Literature was reviewed to develop an understanding about the applications, control methods, excitation methods and mechanics of rotating and linear electric machines. A bidirectional, two-sided linear machine was designed with two stator cores and a single mover core. The stator windings and mover winding can be independently excited, allowing for three modes: no mover excitation, DC excited mover, and AC excited mover. Simulations results showed that the magnetic flux generated by DC excited stator cores were concentrated in the centre of the mover core. The use of two stator cores eliminates lateral flux in the mover core when it is not excited, minimising attraction and repulsion forces. Parametric analysis showed that flux cutting occurred in all operation modes, verifying that the generator will produce power when operating. Hardware tests produced an output current when the machine is electrically and mechanically excited, verifying the proposed design.

The paper focuses of the interaction between tungsten (W) wire and microwave field in carbon dioxide (CO2) atmosphere. Our experimental set-up uses a microwave plasma generator in order to generate the plasma from the metallic wires. The microwave plasma generator contain a cylindrical cavity - TM_011 propagation modes, commercial source (magnetron) having the 2.45 GHz frequency at 800 W microwave and power supply. In the focal point of the cylindrical cavity we have a high energy of the electromagnetic radiation. The metallic wires from this area will be vaporized and ionized having as effect CO2 dissociation. The electron temperature regarding metallic plasma produced was estimated using the ratio of atomic emission lines acquired by a high definition of the optical multichannel spectrometer. Determination of the CO2 dissociation quantity was estimated measuring of the carbon monoxide (CO) resulting of the CO2 dissociation process. We obtained a high electron temperature of the plasma and a strong dissociation of the CO2.

The evolving multiphase induction generators (MPIG) with more than three phases are receiving prominence in high power generation systems. This paper aims at the development of a comprehensive model of the wind turbine driven seven-phase induction generator (7PIG) along with necessary the power electronic converters and controller for grid interface. The dynamic model of the system is developed in Maltlab/Simulink. Synchronous reference frame phase-locked loop (SRFPLL) system is incorporated for grid synchronization. The modeling aspects are detailed and the system response is observed for various wind velocities. The effectiveness of seven phase induction generator is demonstrated with the fault tolerant capability and high output power with reduced phase current when compared to conventional 3-phase wind generation scheme. The response of the PLL is analyzed and the results are presented.

Isoamyl (E)-3-(3,4-dimethoxyphenyl)acrylate (1) was obtained 95% yield by 2-methyl-6-nitrobenzoic anhydride (MNBA)/4-dimethylaminopyridine (DMAP)-catalyzed reaction at room temperature for 190 minutes in dichloromethane. The structure of isoamyl (E)-3-(3,4-dimethoxyphenyl)acrylate (1) was established by NMR, FTIR, and the high resolution of mass spectroscopies. In vitro sun protection factor evaluation exhibited value of 37.10 ± 0.03 which indicates that isoamyl (E)-3-(3,4-dimethoxyphenyl)acrylate (1) as a sunscreen agent with high protection.

The Universe has a gravitational horizon with a radius R_h = c/H coincident with that of the Hubble sphere. This surface separates null geodesics approaching us from those receding, and as free-falling observers within the Friedmann-Lemaitre-Robertson-Walker spacetime, we see it retreating at proper speed c, giving rise to the eponymously named cosmological model R_h = ct. As of today, this cosmology has passed over 20 observational tests, often better than LCDM. The gravitational radius R_h therefore appears to be highly relevant to cosmological theory, and in this paper we begin to explore its impact on fundamental physics. We calculate the binding energy of a mass m within the horizon and demonstrate that it is equal to mc². This energy is stored when the particle is at rest near the observer, transitioning to a purely kinetic form equal to the particle's escape energy when it approaches R_h. In other words, a particle's gravitational coupling to that portion of the Universe with which it is causally connected appears to be the origin of rest-mass energy.

The purpose of this study is to find out the e-reputation management of the hotel industry, as well as the social media channels used as the tools of hotel e-reputation building. This study used a qualitative approach by analyzing the in-depth interviews with hotel marketing communication practitioners of 15 hotel companies in Bandung City. The findings identified that e-reputation is considered a crucial factor in determining hotel performance due to the change of customers’ behaviors today and identified also three types of e-reputation management activities implemented by hotel companies, such as online activities, offline activities, and online/offline activities. The results of this study have implications for the hospitality industry, as a reference for formulating their marketing strategies.

A machine learning method for classifying Lung UltraSound is here proposed to pro- vide a point of care tool for supporting a safe, fast and accurate diagnosis, that can also be useful during a pandemic like as SARS-CoV-2. Given the advantages (e.g. safety, rapidity, portability, cost-effectiveness) provided by the ultrasound technology over other methods (e.g. X-ray, computer tomography, magnetic resonance imaging), our method was validated on the largest LUS public dataset. Focusing on both accuracy and efficiency, our solution is based on an efficient adaptive ensembling of two EfficientNet-b0 models reaching 100% of accuracy, which, to our knowledge, outperforms the previous state-of-the-art. The complexity of this solution keeps the number of parameters in the same order as an EfficientNet-b0 by adopting specific design choices that are adaptive ensembling with a combination layer, ensembling performed on the deep features, minimal ensemble only two weak models. Moreover, a visual analysis of the saliency maps on sample images of all the classes of the dataset reveals where the focus is on an inaccurate weak model versus an accurate model.

An event occurring within a stationary environment, in the direction toward which an observer self-rotates, is perceived to precede a simultaneous event, in the direction away from which she moves. When self-rotation results from angular acceleration in the dark, perception of space is also distorted, such that the subjective straight-ahead shifts in the opposite direction to motion and temporal event promotion. A reference frameshift theory, based on the special theory of relativity, is proposed to explain these findings. Here, a hyperbolic tangent transformation of objective angular velocity constrains subjective self-rotation velocity within finite bounds, consistent with it being a limited perceptual resource. Identifying this subjective variable with vestibular nystagmus slow-phase angular velocity, the asymptotic perceived self-rotation velocity is estimated at ~200 °⁄s. When included in the Lorentz transformations of the new formalism, this value predicts experimental simultaneity distortion. Hypothetically, the hyperbolic tangent objective-to-subjective transfer function would maximize the differential entropy of the percept, and thereby also the stimulus/percept mutual information, if angular velocities of body rotation encountered in naturalistic environmental interaction have a logistic probability density distribution of scale 100 °⁄s, a proposed experimental test of the scheme.

In this study, the temporal variation in soil salinity dynamics was monitored and analyzed using Electromagnetic Induction (EMI) in an agricultural area in Port Said, Egypt, which is at risk of soil salinization. To assess soil salinity, repeated CMD2 soil apparent electrical conductivity (ECa) measurements were taken and inverted to generate electromagnetic conductivity imaging (EMCI), representing soil electrical conductivity (σ) distribution through time-lapse inversion. This process involved converting EMCI data into salinity cross sections using a site-specific calibration equation that correlates σ with the electrical conductivity of saturated soil paste extract (ECe) for the collected soil samples. The study was performed from August 2021 to April 2023, involving six surveys during two agriculture seasons. The results demonstrated the accurate prediction ability of soil salinity with R2 value of 0.81. The soil salinity cross sections generated on different dates observed changes in the soil salinity distribution. These changes can be attributed to shifts in irrigation water salinity resulting from canal lining, winter rainfall events, and variations in groundwater salinity. This approach is effective for evaluating agricultural management strategies in irrigated areas where it is necessary to continuously track soil salinity to avoid soil fertility degradation and a decrease in agricultural production and farmer’s income.

Phase change refers to the process of maturation and transition from the juvenile to the adult stage. In response to this shift, certain species like chestnut lose the ability to form adventitious roots, thereby hindering the successful micropropagation of adult plants. While auxin is the main hormone involved in adventitious root formation, other hormones, such as ethylene, are also thought to play a role in its induction and development. In this study, experiments were carried out to determine the effects of ethylene on the induction and growth of adventitious roots. The analysis was performed in two types of chestnut microshoots derived from the same tree, a juvenile-like line with high rooting ability derived from basal shoots (P2BS) and a line derived from crown branches (P2CR) with low rooting responses. By means of the application of compounds to modify ethylene content or inhibit its signalling, the potential involvement of this hormone in the in-duction of adventitious roots was analyzed. Our results show that ethylene can modify the rooting competence of mature shoots, while the response in juvenile material was barely affected. To further characterize the molecular reasons underlying this maturation-derived shift in behaviour, specific gene expression analyses were developed. Findings suggest that several mechanisms, including ethylene signalling, auxin transport and epigenetic modifications, relate to the modu-lation of the rooting ability of mature chestnut microshoots and their recalcitrant behaviour.

A novel method proposed in the production of Calophyllum inophyllum biodiesel has been investigated experimentally. In this study, we report the results of biodiesel processing with electromagnetic induction technology. The method used is to compare the results of Calophyllum inophyllum biodiesel processing between conventional, microwave and electromagnetic induction. The degumming, transesterification, and esterification process of the 3 methods are measured by stopwatch to obtain time comparison data. Characteristics of viscosity, density, and Fatty Acid Metil Ester (FAME) were obtained from testing of a Gas Chromatography-mass Spectrometry (GCMS) at the Polytechnic Chemistry Laboratory of the State of Malang. The results show that the biodiesel produced by this method satisfies the biodiesel standards and their characteristics are better than the biodiesel produced by conventional and microwave methods. The electromagnetic induction method also offers a fast and easy route to produce biodiesel with the advantage of increasing the reaction rate and improving the separation process compared to other methods. This advanced technology has the potential to significantly increase biodiesel production with considerable potential to reduce production time and costs.

As customer demand for green products increases in the digital economic era, this study analyses the green innovation of the e-tailer and supplier in drop shipping models. Moreover, drop shipping e-tailers and suppliers with a drop shipping option need to make choices regarding whether to provide green or normal products to the market. When a supplier with a drop shipping option produces green products, more fees may be invested on the production of green products than on normal products. The drop shipping e-tailers and suppliers with a drop shipping option can also choose to sell normal products at a low cost, as before. This study designs four models of drop shipping e-teilers and suppliers with a drop shipping option under different choices, analyzes their operational process in drop shipping models, and investigates five theorems. The optimal pricings decisions and green degree of drop shipping e-tailers and suppliers with a drop shipping option were evaluated in this study. The impacts of the green innovation factor, green elasticity coefficient, manufacturing and distribution costs on the drop shipping e-tailers and suppliers with a drop shipping option, and the effect of other environmental parameters on the green degree of green products are also analyzed through computer simulation. The findings of the simulation analysis provide valuable guidance for e-tailers and suppliers with green innovation in drop shipping models and offer important academic and practical implications for e-commerce and the digital economy.

Introduction: Left atrial hypertension is one of the pathophysiologies of heart failure with preserved ejection fraction. We hypothesized that left atrial pressure response (LAPR) to incremental pacing is higher in patients with atrial fibrillation (AF) and can predict left ventricular diastolic dysfunction. Methods: Patients requiring left atrial access as a part of a therapeutic procedure for AF (n=204, AF group) or supraventricular tachycardia (n=34, control group) were analyzed (male n=183, 54±12 years old). LAPR was measured during incremental pacing. Results: Baseline left atrial pressure and LAPR at all pacing rates were not different between the AF and control groups. They were higher in patients with a high E/e’ (≥ 8) than in those with a low E/e’ (&lt; 8). LAPR at a pacing interval of 400ms and E/e' were positively correlated (r=0.373, p&lt;0.001). Body mass index and a high E/e' were independent predictors of pacing-induced left atrial hypertension. Conclusions: The LAPR to incremental pacing was constant regardless of AF. The non-invasive echocardiographic marker E/e' reflected pacing-induced left atrial hypertension.

Whistler mode waves play a major role in regulating the lifetime of trapped electrons in the Earth's radiation belts. Specifically, whistler mode hiss waves are one of the mechanisms that maintains the slot region between the inner and outer radiation belts. The generation mechanism of hiss is a topic still under debate with at least three prominent theories present in the literature. Lightning generated whistlers in their ducted or non-ducted modes, are considered to be one of the possible sources of hiss. We present a study of new observations from the Radio Receiver Instrument (RRI) on the Enhanced Polar Outflow Probe (ePOP: currently known as SWARM-E). RRI consists of two orthogonal dipole antennas, which enables polarization measurements, when the satellite boresight is parallel to the geomagnetic field. Here we present 75 passes of ePOP - RRI from 2014 - 2018, in which lightning whistlers and hiss waves were observed. In more than 50% of those passes hiss is found to co-exist with the lightning whistlers. Moreover, the whistler observations are correlated with observations of wave power at the lower-hybrid resonance. The observations and a whistler mode ray-tracing study suggest that multiple-hop lightning induced whistlers can be a source of hiss and plasma instabilities in the magnetosphere.

This work presents a unique two-element high-isolated orthogonally CPW-fed UWB Multiple Input Multiple Output (Ultra-wideband) antenna. The antenna is supported by the 52.8 × 29 mm2 FR-4 substrate, which has a dielectric constant of 4.3 and a thickness of 1.6 mm. The suggested MIMO antenna reduces mutual coupling by separating the two single UWB antennas that make up the antenna. The suggested antenna achieves a voltage standing wave ratio (VSWR) of less than two and more than 86% radiation efficiency over the whole range of interest. The antenna's performance is assessed using both modeling and experimentation. Return loss, efficiency, gain, bandwidth, and Voltage Standing Wave Ratio (VSWR) are all factors in which the design performs well. The suggested antenna is evaluated using the CST Microwave Studio. The antenna prototype model is constructed, tested, and measured in order to validate the simulation return-loss results. There is good agreement between the measured and simulated results.

In bioprocess development, the host and the genetic construct for a new biomanufacturing process are selected in the early developmental stages. This decision, made at the screening scale with very limited information about the performance of the selected cell factory in larger reactors, has a major influence on the performance of the final process. To overcome this, scaledown approaches are essential to run screenings that show the real cell factory performance at industrial like conditions. We present a fully automated robotic facility with 24 parallel mini-bioreactors that is operated by a model based adaptive input design framework for the characterization of clone libraries under scale-down conditions. The cultivation operation strategies are computed and continuously refined based on a macro-kinetic growth model that is continuously re-fitted to the available experimental data. The added value of the approach is demonstrated with 24 parallel fed-batch cultivations in a mini-bioreactor system with eight different Escherichia coli strains in triplicate. The 24 fed-batches ran under the desired conditions generating sufficient information to define the fastest growing strain in an environment with varying glucose concentrations similar to industrial scale bioreactors.

In this paper, a robust nonlinear dynamic controller is designed for a wind turbine with a permanent magnet synchronous generator. The wind turbine is subject to variations in all the parameters appearing in its mathematical model. Furthermore, the wind velocity is considered unavailable for direct measurement. This situation is of particular interest in practical applications, where only the nominal parameter values are known, and accurate wind velocity measurement is challenging due to perturbations caused by the turbine itself, even with appropriate sensors. The problem addressed in this work involves tracking the reference angular velocity corresponding to the wind velocity. To achieve accurate tracking, appropriate compensation of the perturbation terms resulting from parameter uncertainties and wind estimation errors is required. To address this problem, an estimator of the wind velocity is utilized, along with high–order sliding mode parameter estimators, to ensure high–performance operation of the turbine.

Synchronous homopolar machines (SHM) with excitation winding on the stator have attracted the attention of researchers for many decades due to their high reliability. They are used in a variety of applications such as aircraft and railway generators and traction motors. At the same time, the three-dimensional structure of their magnetic circuit makes the problem of their analysis and optimization challenging. This problem becomes even more complicated when considering an SHM with hybrid excitation, with ferrite magnets in the rotor slots. The article proposes a mathematical procedure for optimizing a synchronous homopolar generator with hybrid excitation based on the single-criterion Nelder-Mead method and two-dimensional finite element analysis (FEA). The use of the Nelder-Mead method compared to multicriteria methods and 2D FEA compared to 3D FEA makes possible to significantly reduce the computational burden. As a result of optimization, the power loss and torque ripples of the generator are significantly reduced. The article also compares the characteristics of synchronous homopolar generators with and without ferrite magnets.

Steam Generator Level Control System (SGLCS) is one of the key instrumentations and control subsystems to ensure the safe operation of nuclear power plants. It is highly recommended to perform reliability analysis for SGLCS for making better maintenance strategy. SGLCS is a digital control system with complex redundant configuration and failure\self-diagnosis\repair action, traditional fault tree is not applicable due to its static property, Markov model is not a good choice too because of heavy burden of creating state transition graph for even medium-size system. Boolean Logic Driven Markov Process (BDMP) can describe complex failure-repair state transition via ‘trigger link’ and three kinds of leaf nodes, as well as keep compact and easy-read struct like fault tree. So BDMP is adopted to analysis reliability of SGLCS. Graphical BDMP modeling environment KB3 and Monte Carlo simulator YAMS is used for BDMP modeling and quantitative analysis respectively, and unavailability of SGLCS is obtained. The contribution of three parts of SGLCS to the unavailability of the system is also evaluated, and it is found that the water supply flow control part contributes the most to the failure of SGLCS.

For our research on droplet deformation and breakup in scaled high-pressure homogenizing units we developed a pressure stable inline droplet generator. It consists of an optically accessible flow channel with a combination of stainless steel and glass capillaries and a 3D printed orifice. The droplet size is determined online by live image analysis. The influence of the orifice diameter, the mass flow of the continuous phase and the mass flow of the disperse phase on the droplet diameter was investigated. Furthermore, the droplet detachment mechanisms were identified. Droplet diameters with small diameter fluctuation between 175 µm and 500 µm could be realized, which allows a precise adjustment of the Ca and We Number in the subsequent scaled high pressure homogenizer disruption unit. The determined influence of geometry and process parameters on the resulting droplet size and droplet detachment mechanism agreed well with literature on microfluidics. Furthermore, droplet trajectories in an exemplary scaled high-pressure homogenizer disruption unit are presented which show that the droplets can be reinjected on a trajectory close to the center axis or close to the wall, which should result in different stresses on the droplets.

Turbine generator operates with complex cooling system due to the challenge in controlling the peak temperature of the stator bar caused by ohm loss, which is unavoidable. Therefore, it is important to characterise and quantifies the thermal performance of the cooling system. The focus of the present research is to investigate the heat transfer and pressure loss characteristics of typical cooling system, so-called stator ventilation duct. A real scale model was built at its operating conditions for the present study. The direction of cooling air is varied to consider its operation condition, so that there are (1) outward flow and (2) inward flow cases. In addition, the effect of (3) cross flow (inward with cross flow case) is also studied. The transient heat transfer method using thermochromic liquid crystals is implemented to measure full surface heat transfer distribution. A series of Computational Fluid Dynamics analysis is also conducted to support the observation from the experiment. For the inward flow case, the results suggest that the average Nusselt number of the 2nd duct is about 30% higher than the 3rd duct. The trend is similar with the effect of cross flow. The CFD results are in good agreement with the experimental data.

Active flow control of canonical laminar separation bubbles by steady and harmonic vortex generator jets (VGJs) was investigated using direct numerical simulations. Both control strategies were found to be effective in controlling the laminar boundary-layer separation. However, the present results indicate that using the same blowing amplitude, harmonic VGJs were more effective and efficient in reducing the separated region than the steady VGJs considering the fact that the harmonic VGJs use less momentum than the steady case. For steady VGJs, longitudinal structures formed immediately downstream of injection location led to formation of hairpin-type vortices causing an earlier transition to turbulence. Symmetric hairpin vortices were shown to develop downstream of the forcing location for the harmonic VGJs as well. However, the increased control effectiveness for harmonic VGJs flow control strategy is attributed to the fact that shear-layer instability mechanism was exploited. As a result, disturbances introduced by VGJs were strongly amplified leading to development of large-scale coherent structures, which are very effective in increasing the momentum exchange, thus, limiting the separated region.

The E-learning system has achieved great development after the pandemic. In this work, we proposed three artificial intelligence-based enhancements to our linguistic interactive E-learning system from different aspects. Compared with the original phonetic transcription exam system, our enhancements include an MFCC+CNN-based disordered speech classification module, a Transformer-based Grapheme-to-Phoneme converter, and a Tacotron2-based IPA-to-Speech speech synthesis system. This work not only provides a better experience for the users of this system but also explores the utilization of artificial intelligence technologies in the E-learning field and linguistic field.

The adverse relationship between viral hepatitis and pregnancy in developing countries was seen as a reflection of retrospective biased hospital-based data collection by the West. However, the discovery of HEV from an epidemic of non-A, non-B hepatitis in Kashmir and documenting increased incidence and severity of hepatitis E in pregnancy from a house-to-house survey unmasked the unholy alliance. Among the family of HEV’s, genotype (gt)-1, with a unique ORF4-encoded protein enhancing viral polymerase activity and viral replication, is the sole HEV that shows this adverse relationship. The epidemics caused by HEV-gt1 and not by HEV-gt2 show adverse relationship with pregnancy. The pathogenesis of the unholy alliance is complex and at present not well understood. Possibly multiple factors play a role in causing severe liver disease in the mother including: infection, replication and damage to the maternal-foetal interface by HEV-gt1; vertical transmission of HEV to foetus causing severe foetal/neonatal hepatitis; and combined viral and hormone related immune dysfunction of diverse nature in the mother promoting viral replication. Management is multidisciplinary and needs a close watch for the development and management of ALF. Preliminary data suggest beneficial maternal outcomes by early termination of pregnancy in patients with lower grades of encephalopathy.

Boron carbide (B4C) powders with defined stoichiometry, high crystallinity, minimal impurity content, and a fine particle size are imperative for realizing the exceptional properties of this compound in advanced high-technology applications. Nevertheless, achieving the desired stoi-chiometry and particle size using traditional synthesis methods, which rely on prolonged, high-temperature processes, can be challenging. The primary objective of this study is to syn-thesize fine B4C powders characterized by high crystallinity and a sub-micron particle size, em-ploying a fast, and energy-efficient method. B4C powders are synthesized from elemental boron and carbon in a high-frequency induction heating furnace using the Electromagnetic Induction Synthesis (EMIS) method. The rapid heating rate achieved through contactless heating promotes the ignition and propagation of the exothermic chemical reaction between boron and carbon. Additionally, electromagnetic effects accelerate atomic diffusion, allowing the reaction to be completed in an exceptionally short timeframe. The grain size and crystallinity of B4C can be finely tuned by adjusting various process parameters, including the post-ignition holding temperature and the duration of heating. As a result, fine B4C powders can be synthesized in under 10 minutes. Moreover, these synthesized B4C powders exhibit high resistance to oxidation when exposed to air.

Induction heating (IH) technology is widely recognized and utilized in residential applications due to its high efficiency and safe operating characteristics. Resonant inverter circuits are widely used in IH systems because of their high efficiency and ability to perform soft-switching. Among the various resonant inverters used in IH systems, the single-switch quasi-resonant (SSQR) inverter topology is typically preferred for low-cost and low-output-power applications. Despite its cost advantage, the SSQR topology has a relatively narrow soft-switching range, which can be unstable depending on the electrical parameters of the load and the resonant converter circuit. Accurately determining the capacitance value of the resonant capacitor and the inductance value of the induction coil, which are the key circuit elements of the SSQR induction cooker, is crucial for designing a reliable, efficient, and durable cooking system. In other words, there exists a critical relationship between the resonant converter circuit parameters, load characteristics, and safe operating conditions. Additionally, when considering closed-loop control methods used for power control and safety, selecting appropriate resonant circuit elements becomes vital in ensuring both reliable and efficient operation. This paper focuses on a novel and simplified design method for the SSQR inverter utilized in household appliances. The proposed method and its advantages in terms of the safe operating area of the switch are theoretically investigated and verified through simulations and prototype circuits.

Polyploidy induction is recognized as one of the major evolutionary processes presenting remark-able morphological, physiological, and genetic variations in plants. Soybean (Glycine max L.), also known as soja bean or soya bean, is an annual leguminous crop of the pea family (Fabaceae) that shares a paleopolypoidy history, dating back to approximately 56.5 million years ago with other leguminous crops such as cowpea and other Glycine specific polyploids. This crop has been documented as one of the polyploid complex species among legumes whose gene evolution and result-ant adaptive growth characteristics, following induced polyploidization has not been fully explored. Furthermore, there are no successfully established in vivo or in vitro based polyploidy in-duction protocols that have been reported so far, particularly, with the intention to develop mutant plants showing strong resistance to abiotic salinity stress. This review, therefore, describes the role of synthetic polyploid plant production in soybean for the mitigation against high soil salt stress levels, and how this evolving approach could be used to further enhance nutritional, pharmaceutical and economic industrial value of soybeans, including addressing challenges involved during the polyploidization process.

We present here a five hours experimentation of a didactical path about the electromagnetic induction addressed to students of the last year of an Italian scientific high school and oriented to better understand the physical origin of the induced electromotive force. The expression of the induced electromotive force as the sum of the term linked to the time variation of the magnetic field and of the motional one has been obtained in a detailed way, still suitable for presentation at high school. Many examples have been proposed to the students in order to clarify the conceptual physical knots. The students’ responses to a 6-questions multiple choice questionnaire have been analyzed. It emerged that our approach is concretely feasible although we find the well-known difficulties in calculating flux and circulation of a vector field. Furthermore, it emerged that an integral approach to the problem masks the understanding of the nature of the forces acting locally on the charges. Hence our proposal of a “redefinition” of the induced electric field in terms of the magnetic vector potential is also presented.